MPC564MZP66 Freescale Semiconductor, MPC564MZP66 Datasheet - Page 122

• Manufacturer Part Number: MPC564MZP66
• Description: IC MCU 512K FLASH 66MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP66

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Signal Descriptions
2-24
11:13
14:15
17:19
22:24
Bits
1:3
4:5
16
20
21
25
0
6
7
8
PREDIS_
PPMPAD
TCNC
PPMV
MDO6
Name
PCSV
MPI7
MPI8
MPI9
MPI6
EN
—
—
—
—
Enable for the Pre-discharge circuit to allow 5 volt external devices on the external data bus.
0 Bus pre-discharge disabled
1 Bus pre-discharge enabled
Note: This bit is reserved in 66-MHz implementations.
Reserved
Controls the function on the following pads: TXD2/QGPO2/C_CNTX0, RXD2/QGPI2/C_CNRX0,
MPIO32B11/C_CNRX0, MPIO32B12/C_CNTX0. Refer to
Controls the pad MPIO32B7/MPWM5.
0 MPIO32B7 function will be selected.
1 MPWM5 function will be selected.
Controls the pad MPIO32B8/MPWM20.
0 MPIO32B8 function will be selected.
1 MPWM20 function will be selected.
Controls the pad MPIO32B9/MPWM21.
0 MPIO32B9 function will be selected.
1 MPWM21 function will be selected.
Control the PPM module pads: MPIO32B14/PPM_RX0, MPIO32B15/PPM_TX0,
MPWM2/PPM_TX1, MPWM3/PPM_RX1, MPIO32B10/PPM_TSYNC, MPIO32B13/PPM_TCLK.
Refer to
Reserved
Selects the voltage of the PPM pads.
0 The voltage will be 2.6 V.
1 The voltage will be 5 V.
Reserved
Selects the functionality of MDO6
0 The pad MPIO32B6/MPWM4/MDO6 will function as MDO6, and the pad MPWM18/MDO6 will
1 The pad MPWM18/MDO6 will function as MDO6, and the pad MPIO32B6/MPWM4/MDO6 will
This selection is enabled only if full port mode is implemented in the READI module, if full port
mode is not selected then MPWM18/MDO6 will function as MPWM18, and
MPIO32B6/MPWM4/MDO6 will function according to MPI6 bit.
NOTE: It is recommended to use MPIO32B6/MPWM4/MDO6 for the Nexus port as MDO6 is
enabled from reset.
Controls the pad MPIO32B6/MPWM4/MDO6.
0 MPIO32B6 function will be selected.
1 MPWM4 function will be selected.
This bit will be disabled if full port mode is enabled in the READI module, and MDO6 bit is logic ‘0’.
Reserved
Selects the polarity of QSMCM module QSPI PCS signals in the PCS expanded mode.
0 Selects Active High.
1 Selects Active Low.
function as MPWM18.
function according to MPI6 bit.
Table
MPC561/MPC563 Reference Manual, Rev. 1.2
2-8.
Table 2-6. PDMCR2 Field Description
Description
Table
2-7.
Freescale Semiconductor