MPC564MZP66 Freescale Semiconductor, MPC564MZP66 Datasheet - Page 879

• Manufacturer Part Number: MPC564MZP66
• Description: IC MCU 512K FLASH 66MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP66

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Freescale Semiconductor
13:14
9:10
Bits
4:5
6:8
11
12
15
0
1
2
3
DBGC[0:1]
Name
EARB
BDRV
ATWC
EBDF
BDIS
BPS
IWS
—
—
IP
External arbitration — Refer to
arbitration. The default value is that internal arbitration hardware is used.
0 Internal arbitration is performed
1 External arbitration is assumed
Initial interrupt prefix — This bit defines the initial value of the MSR[IP] immediately after reset. The
MSR[IP] bit defines the Interrupt Table location.
0 MSR[IP] = 0 after reset
1 MSR[IP] = 1 after reset
The default value is 0. See
Bus pins drive strength — This bit determines the bus pins’ (address, data, and control) driving
capability to be either full or reduced drive. The bus default drive strength is full; upon default, it also
causes the CLKOUT drive strength to be full. See
default state of COM[1] in the SIUMCR.
0 Full drive
1 Reduced drive
Boot disable — If the BDIS bit is set, then memory controller is not activated after reset. If it is cleared
then the memory controller bank 0 is active immediately after reset such that it matches any addresses.
If a write to the OR0 register occurs after reset this bit definition is ignored. The default value is that the
memory controller is enabled to control the boot with the CS0 pin. See
Chip-Select
0 Memory controller bank 0 is active and matches all addresses immediately after reset
1 Memory controller is not activated after reset.
Boot port size — This field defines the port size of the boot device on reset (BR0[PS]). If a write to the
OR0 register occurs after reset this field definition is ignored. See
information.
00 32-bit port (default)
01 8-bit port
10 16-bit port
11 Reserved
Reserved. These bits must not be high in the reset configuration word.
Debug pins configuration — See
this field definition. The default value is that these pins function as: VFLS[0:1], BI, BR, BG and BB. See
Table
Reserved.
Address type write enable configuration — The default value is that these pins function as WE pins.
0 WE[0:3]/BE[0:3]/AT[0:3] functions as WE[0:3]/BE[0:3]
1 WE[0:3]/BE[0:3]/AT[0:3] functions as AT[0:3]
See
External bus division factor — This field defines the initial value of the external bus frequency. The
default value is that CLKOUT frequency is equal to that of the internal clock (no division). See
Interlock write select — This bit determines which interlock write operation should be used during the
clear censorship operation.
IWS always comes from the UC3FCFIG, it will never use the external reset configuration word
(RSTCONF=0) or the default internal reset configuration word (RSTCONF=1 and HC=1).
0 Interlock write is a write to any UC3F array location
1 Interlock write is a write to the UC3FMCR register.
Table
6-8.
6-7.
Operation” for more information.
MPC561/MPC563 Reference Manual, Rev. 1.2
Table 21-6. RCW Bit Descriptions
Table 3-11
Section 9.5.7, “Arbitration
Section 6.2.2.1.1, “SIU Module Configuration Register
for more information.
Description
Table 6-7
Phase” for a detailed description of Bus
for more information. BDRV controls the
Table 10-5
Section 10.7, “Global (Boot)
CDR3 Flash (UC3F) EEPROM
and
Table 10-8
(SIUMCR)” for
Table
for more
21-17
8-9.