R88M-W75030T-S1 Omron, R88M-W75030T-S1 Datasheet - Page 220

• Manufacturer Part Number: R88M-W75030T-S1
• Description: SERVO MOTOR 750W 200V
• Manufacturer: Omron

Specifications of R88M-W75030T-S1

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: R88MW75030TS1

Note 1. The normal setting is 0. When using an External Regeneration Resistor, set the External Re-
Note 2. The upper limit is the maximum output capacity (W) of the applicable Servo Driver.
Note 3. If the Servo Driver is used with the CJ1W-MCH71 or CS1W-MCH71, this parameter will be
Note 4. If the Servo Driver is used with the CJ1W-MCH71 or CS1W-MCH71, this parameter will be
Note 5. If the Servo Driver is used with the CJ1W-MCH71 or CS1W-MCH71, this parameter will be
4-3-2 Important Parameters
4-24
Operation
eter No.
Pn819
Pn81B
Pn81C
Pn81D
Pn81E
Pn81F
Pn820
Pn822
Pn824
Pn825
Pn900
to
Pn910
Pn920
to
Pn95F
Param-
This section explains the user parameters you need to set and check before using the
Servomotor and Servo Driver. If these parameters are set incorrectly, there is a risk of
the Servomotor not rotating, and of a malfunction. Set the parameters to suit your
system.
Final
travel dis-
tance to
return to
zero point
Not used.
Not used.
Not used.
Not used.
Not used.
Not used.
Not used.
Not used.
Not used.
Not used.
Not used.
ter name
Parame-
generation Resistor capacity (W).
set to 0032.
If parameters are edited with the WMON-ML2 connected, this parameter will set to 0000.
If this happens, you must reset this parameter to 0032 from the CJ1W-MCH71 or CS1W-
MCH71.
set to 0023. If parameters are edited with the WMON-ML2 connected, this parameter will set
to 0000. If this happens, you must reset this parameter to 0023 from the CJ1W-MCH71 or
CS1W-MCH71.
set to 0024. If parameters are edited with the WMON-ML2 connected, this parameter will set
to 0000. If this happens, you must reset this parameter to 0024 from the CJ1W-MCH71 or
CS1W-MCH71.
Sets the distance from the latch signal input position to the origin,
for when origin search is executed.
Note: If the final travel distance is in the opposite direction from
the origin return direction or if the distance is short, operation is
reversed after decelerating to a stop.
(Do not change setting.)
(Do not change setting.)
(Do not change setting.)
(Do not change setting.)
(Do not change setting.)
(Do not change setting.)
(Do not change setting.)
(Do not change setting.) (See note 4.)
(Do not change setting.) (See note 5.)
(Do not change setting.)
(Do not change setting.)
Digit
No.
Name
Setting
Explanation
Explanation
100
0
0
0
0000
0
0
0
0000
0000
Default
setting
---
---
---
---
---
---
---
---
---
---
---
Command
unit
Unit
− 1073741823
to
1073741823
---
---
---
---
---
---
---
---
---
---
---
Setting
range
Chapter 4
power?
---
---
---
---
---
---
---
---
---
---
---
---
Restart