SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 384
SAM9G10
Manufacturer Part Number
SAM9G10
Description
Manufacturer
Atmel Corporation
Datasheets
1.SAM9261.pdf
(1274 pages)
2.SAM9261.pdf
(43 pages)
3.SAM9G10.pdf
(750 pages)
4.SAM9G10.pdf
(39 pages)
Specifications of SAM9G10
Flash (kbytes)
0 Kbytes
Pin Count
217
Max. Operating Frequency
266 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
96
Ext Interrupts
96
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
1
Uart
4
Ssc
3
Sd / Emmc
1
Graphic Lcd
Yes
Video Decoder
No
Camera Interface
No
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
16
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.08 to 1.32
Fpu
No
Mpu / Mmu
No/Yes
Timers
3
Output Compare Channels
3
Input Capture Channels
3
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 384 of 1274
- Download datasheet (30Mb)
29.8.2.1
29.8.2.2
384
384
SAM9G35
SAM9G35
Byte Write Access
Byte Select Access
Byte write access supports one byte write signal per byte of the data bus and a single read
signal.
Note that the SMC does not allow boot in Byte Write Access mode.
In this mode, read/write operations can be enabled/disabled at a byte level. One byte-select line
per byte of the data bus is provided. One NRD and one NWE signal control read and write.
Figure 29-7
mode, on NCS3 (BAT = Byte Select Access).
• For 16-bit devices: the SMC provides NWR0 and NWR1 write signals for respectively byte0
• For 32-bit devices: NWR0, NWR1, NWR2 and NWR3, are the write signals of byte0 (lower
• For 16-bit devices: the SMC provides NBS0 and NBS1 selection signals for respectively
• For 32-bit devices: NBS0, NBS1, NBS2 and NBS3, are the selection signals of byte0 (lower
(lower byte) and byte1 (upper byte) of a 16-bit bus. One single read signal (NRD) is provided.
byte), byte1, byte2 and byte 3 (upper byte) respectively. One single read signal (NRD) is
provided.
byte0 (lower byte) and byte1 (upper byte) of a 16-bit bus.
byte), byte1, byte2 and byte 3 (upper byte) respectively. Byte Select Access is used to
connect two 16-bit devices.
Byte Write Access is used to connect 2 x 8-bit devices as a 16-bit memory.
Byte Write Access is used to connect 4 x 8-bit devices as a 32-bit memory.
Byte Write option is illustrated on
Byte Select Access is used to connect one 16-bit device.
shows how to connect two 16-bit devices on a 32-bit data bus in Byte Select Access
Figure
29-6.
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
Related parts for SAM9G10
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: