SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 948

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

41.8.12
Name:
Address:
Access:
• EOCx: End of Conversion x
0 = Corresponding analog channel is disabled, or the conversion is not finished. This flag is cleared when reading the cor-
responding ADC_CDRx registers.
1 = Corresponding analog channel is enabled and conversion is complete.
• XRDY: Touchscreen XPOS Measure Ready
0 = No Measure has been performed since the last read of ADC_XPOSR.
1 = At least one Measure has been performed since the last read of ADC_ISR.
• YRDY: Touchscreen YPOS Measure Ready
0 = No Measure has been performed since the last read of ADC_YPOSR.
1 = At least one Measure has been performed since the last read of ADC_ISR.
• PRDY: Touchscreen Pressure Measure Ready
0 = No Measure has been performed since the last read of ADC_PRESSR.
1 = At least one Measure has been performed since the last read of ADC_ISR.
• DRDY: Data Ready
0 = No data has been converted since the last read of ADC_LCDR.
1 = At least one data has been converted and is available in ADC_LCDR.
• GOVRE: General Overrun Error
0 = No General Overrun Error occurred since the last read of ADC_ISR.
1 = At least one General Overrun Error has occurred since the last read of ADC_ISR.
• COMPE: Comparison Error
0 = No Comparison Error since the last read of ADC_ISR.
1 = At least one Comparison Error has occurred since the last read of ADC_ISR.
948
PENS
EOC7
31
23
15
–
–
7
SAM9G35
ADC Interrupt Status Register
NOPEN
PRDY
EOC6
30
22
14
ADC_ISR
0xF804C030
Read-only
–
6
EOC5
YRDY
PEN
29
21
13
–
5
XRDY
EOC4
28
20
12
–
–
4
EOC11
EOC3
27
19
11
–
–
3
COMPE
EOC10
EOC2
26
18
10
–
2
GOVRE
EOC9
EOC1
25
17
–
9
1
11053B–ATARM–22-Sep-11
DRDY
EOC8
EOC0
24
16
–
8
0