ATXMEGA256A3B-MH Atmel, ATXMEGA256A3B-MH Datasheet - Page 76

• Manufacturer Part Number: ATXMEGA256A3B-MH
• Description: MCU AVR 256KB FLASH A3B 64-QFN
• Manufacturer: Atmel
• Series: AVR® XMEGAr

Specifications of ATXMEGA256A3B-MH

• Core Processor: AVR
• Core Size: 8/16-Bit
• Speed: 32MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 49
• Program Memory Size: 256KB (128K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.6 V ~ 3.6 V
• Data Converters: A/D 16x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-MLF®, 64-QFN
• Processor Series: ATXMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit, 16 bit
• Data Ram Size: 16 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 49
• Number Of Timers: 7
• Operating Supply Voltage: 1.6 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 8 Channel
• On-chip Dac: 12 bit, 2 Channel
• For Use With: ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMRATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ATXMEGA256A3B-MU; ATXMEGA256A3B-MU

7. System Clock and Clock options
7.1
7.2
8077H–AVR–12/09
Features
Overview
•
•
•
•
•
•
•
•
•
XMEGA has a flexible clock system, supporting a large number of clock sources. It incorporates
both accurate integrated oscillators, and external crystal oscillators and resonators. A high fre-
quency Phase Locked Loop (PLL) and clock prescalers can be used to generate a wide range of
clock frequencies. A calibration feature (DFLL) is available, and can be used for automatic run-
time calibration of the internal oscillators. A Crystal Oscillator Failure Monitor can be enabled to
issue a Non-Maskable Interrupt and switch to internal oscillator if the external oscillator fails.
After reset, the device will always start up running from the 2 MHz internal oscillator. During nor-
mal operation, the System Clock source and prescalers can be changed from software at any
time.
Figure 7-1 on page 77
need to be active at a given time. The clocks to the CPU and peripherals can be stopped using
sleep modes and power reduction registers as described in
page
Fast start-up time
Safe run-time clock switching
Internal Oscillators:
External clock options
PLL with internal and external clock options with 1 to 31x multiplication
Clock Prescalers with 1 to 2048x division
Fast peripheral clock running at 2 and 4 times the CPU clock speed
Automatic Run-Time Calibration of internal oscillators
Crystal Oscillator failure detection
– 32 MHz run-time calibrated RC oscillator
– 2 MHz run-time calibrated RC oscillator
– 32.768 kHz calibrated RC oscillator
– 32 kHz Ultra Low Power (ULP) oscillator with 1 kHz output
– 0.4 - 16 MHz Crystal Oscillator
– 32.768 kHz Crystal Oscillator
– External clock
95.
presents the principal clock system in the XMEGA. All of the clocks do not
”Power Management and Sleep” on
XMEGA A
76