MOD5234-100IR NetBurner Inc, MOD5234-100IR Datasheet - Page 161
MOD5234-100IR
Manufacturer Part Number
MOD5234-100IR
Description
MOD5234 10/100 ETHERNET MODULE
Manufacturer
NetBurner Inc
Type
Controllers & Processorsr
Datasheets
1.MOD5272-100IR.pdf
(3 pages)
2.MOD5234-100IR.pdf
(4 pages)
3.MOD5234-100IR.pdf
(754 pages)
Specifications of MOD5234-100IR
Interface
I²C, SPI, UART
Voltage - Supply
2.5V
Mounting Type
Surface Mount
Package / Case
Module
Product
Modules
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Format
-
Baud Rates
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
Q4483564
- Current page: 161 of 754
- Download datasheet (13Mb)
Please note that the frequency modulation system is dependent upon several factors. The
accuracies of the VDDPLL/VSSPLL voltage, of the crystal oscillator frequency, and of the
manufacturing variation.
For example, if a 5% accurate supply voltage is utilized, then a 5% modulation depth error will
result. If the crystal oscillator frequency is skewed from 8MHz, the resulting modulation
frequency will be proportionally skewed. Finally, the error due to the manufacturing and
environment variation alone can cause the frequency modulation depth error to be greater than
20%.
Freescale Semiconductor
4. Write a value of RFD = RFD + 1 to the RFD field of the SYNCR to ensure the maximum
5. Program the desired modulation rates and depths to the RATE and DEPTH fields in the
6. Allow time for the calibration sequence. Wait for the PLL to lock (the LOCK bit to set in
system frequency is not exceeded during the calibration routine.
SYNCR. This action initiates the calibration sequence.
the SYNSR). At this time CALDONE should be asserted. CALPASS will be asserted if
the calibration was successful. If not, the calibration can be re-initiated by repeating from
step 2. When the PLL achieves lock, write the desired RFD value.
F
F
max
min
f
Fmax = f
Fmin = f
Fmod = Fref/Q where Q = {40, 80}
Figure 7-6. Frequency Modulation Waveform
sys/2
sys/2
MCF5235 Reference Manual, Rev. 2
∆Fm
+ {1%, 2%}
- {1%, 2%}
∆t
=
----------- -
F
mod
1
∆Fm
Functional Description
t
7-17
Related parts for MOD5234-100IR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MCU, MPU & DSP Development Tools MOD5234 MODULE
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools MOD5234 Core Module Development Kit
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
BOARD SERIAL-ETHERNET 512K FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE FLASH MOD5272
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE 512KB FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
DUAL PORT SERIAL-ETHERNET
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE 512KB FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
KIT DEVELOP NETWORK FOR MOD5282
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
KIT DEVELOP NETWORK FOR MOD5272
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
DUAL PORT SERIAL-ETHERNET
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
Ethernet Modules & Development Tools 32 Bit 66MHz 40 Pin DIP Industrial Temp
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
Ethernet ICs 32bit 147MHz CAN-to- Ethnt Device IndTemp
Manufacturer:
NetBurner Inc
Datasheet: