MOD5234-100IR NetBurner Inc, MOD5234-100IR Datasheet - Page 198
MOD5234-100IR
Manufacturer Part Number
MOD5234-100IR
Description
MOD5234 10/100 ETHERNET MODULE
Manufacturer
NetBurner Inc
Type
Controllers & Processorsr
Datasheets
1.MOD5272-100IR.pdf
(3 pages)
2.MOD5234-100IR.pdf
(4 pages)
3.MOD5234-100IR.pdf
(754 pages)
Specifications of MOD5234-100IR
Interface
I²C, SPI, UART
Voltage - Supply
2.5V
Mounting Type
Surface Mount
Package / Case
Module
Product
Modules
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Format
-
Baud Rates
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
Q4483564
- Current page: 198 of 754
- Download datasheet (13Mb)
Chip Configuration Module (CCM)
9.4.3
During reset configuration, the CS0 chip select pin is configured to select an external boot device.
In this case, the V (valid) bit in the CSMR0 register is ignored, and CS0 is enabled after reset. CS0
is asserted for the initial boot fetch accessed from address 0x0000_0000 for the Stack Pointer and
address 0x0000_0004 for the program counter (PC). It is assumed that the reset vector loaded from
address 0x0000_0004 causes the CPU to start executing from external memory space decoded by
CS0.
9.4.4
Output pad strength is determined during reset configuration as shown in
is exited, the output pad strength configuration can be changed by programming the LOAD bit of
the chip configuration register.
9.4.5
The clock mode is selected during reset and reflected in the PLLMODE, PLLSEL, and PLLREF
bits of SYNSR. Once reset is exited, the clock mode cannot be changed.
clock mode selection during reset configuration.
9-10
1
External clock mode; PLL disabled
1:1 PLL mode
Normal PLL mode; external clock reference
Normal PLL mode; crystal oscillator reference
There is no default configuration for clock mode selection. The actual values for the CLKMOD pins must always be driven
during reset. Once out of reset, the CLKMOD pins have no effect on the clock mode selection.
Boot Device Selection
Output Pad Strength Configuration
Clock Mode Selection
1
Output pads configured for partial strength
Output pads configured for full strength
Clock Mode
Modifying the default configurations is possible only if the external RCON pin is asserted low.
Optional Pin Function Selection
Table 9-10. Output Pad Driver Strength Selection
Table 9-11. Clock Mode Selection
MCF5235 Reference Manual, Rev. 2
CLKMOD[1] CLKMOD[0]
0
0
1
1
0
1
0
0
PLLMODE
RCON[RLOAD]
D21 driven high
D21 driven low
1
0
1
1
1
PLL SYNSR Bits
Table 9-11
Table
1
PLLSEL
Freescale Semiconductor
0
0
1
1
9-10. Once reset
summarizes
PLLREF
0
0
0
1
Related parts for MOD5234-100IR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MCU, MPU & DSP Development Tools MOD5234 MODULE
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools MOD5234 Core Module Development Kit
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
BOARD SERIAL-ETHERNET 512K FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE FLASH MOD5272
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE 512KB FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
DUAL PORT SERIAL-ETHERNET
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
PROCESSOR MODULE 512KB FLASH
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
KIT DEVELOP NETWORK FOR MOD5282
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
KIT DEVELOP NETWORK FOR MOD5272
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
DUAL PORT SERIAL-ETHERNET
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
Ethernet Modules & Development Tools 32 Bit 66MHz 40 Pin DIP Industrial Temp
Manufacturer:
NetBurner Inc
Datasheet:
Part Number:
Description:
Ethernet ICs 32bit 147MHz CAN-to- Ethnt Device IndTemp
Manufacturer:
NetBurner Inc
Datasheet: