ATxmega128B1 Atmel Corporation, ATxmega128B1 Datasheet - Page 119

• Manufacturer Part Number: ATxmega128B1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 53
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 10
• Input Capture Channels: 10
• Pwm Channels: 10
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

11. Interrupts and Programmable Multilevel Interrupt Controller
11.1
11.2
Figure 11-1. PMIC overview
8291A–AVR–10/11
Peripheral 1
Peripheral n
Features
Overview
INT LEVEL
INT REQ
INT ACK
INT LEVEL
INT LEVEL
INT REQ
INT REQ
INT ACK
INT ACK
•
•
•
•
Interrupts signal a change of state in peripherals, and this can be used to alter program execu-
tion. Peripherals can have one or more interrupts, and all are individually enabled and
configured. When an interrupt is enabled and configured, it will generate an interrupt request
when the interrupt condition is present. The programmable multilevel interrupt controller (PMIC)
controls the handling and prioritizing of interrupt requests. When an interrupt request is acknowl-
edged by the PMIC, the program counter is set to point to the interrupt vector, and the interrupt
handler can be executed.
All peripherals can select between three different priority levels for their interrupts: low, medium,
and high. Interrupts are prioritized according to their level and their interrupt vector address.
Medium-level interrupts will interrupt low-level interrupt handlers. High-level interrupts will inter-
rupt both medium- and low-level interrupt handlers. Within each level, the interrupt priority is
decided from the interrupt vector address, where the lowest interrupt vector address has the
highest interrupt priority. Low-level interrupts have an optional round-robin scheduling scheme to
ensure that all interrupts are serviced within a certain amount of time.
Non-maskable interrupts (NMI) are also supported, and can be used for system critical
functions.
Interrupt Controller
Short and predictable interrupt response time
Separate interrupt configuration and vector address for each interrupt
Programmable multilevel interrupt controller
Interrupt vectors optionally placed in the application section or the boot loader section
CTRL
– Interrupt prioritizing according to level and vector address
– Three selectable interrupt levels for all interrupts: low, medium and high
– Selectable, round-robin priority scheme within low-level interrupts
– Non-maskable interrupts for critical functions
LEVEL Enable
STATUS
decoder
INTPRI
Priority
CPU.SREG
Global
Interrupt
Enable
Atmel AVR XMEGA B
CPU INT REQ
CPU INT ACK
CPU ”RETI”
Wake-up
Controller
Sleep
CPU
119