ATxmega128B1 Atmel Corporation, ATxmega128B1 Datasheet - Page 144

• Manufacturer Part Number: ATxmega128B1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 53
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 10
• Input Capture Channels: 10
• Pwm Channels: 10
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

12.14 Register Descriptions – Port Configuration
12.14.1
12.14.2
12.14.3
8291A–AVR–10/11
MPCMASK – Multi-pin Configuration Mask Register
VPCTRLA – Virtual Port-map Control Register A
VPCTRLB – Virtual Port-map Control Register B
• Bit 7:0 – MPCMASK[7:0]: Multi-pin Configuration Mask
The MPCMASK register enables configuration of several pins of a port at the same time. Writing
a one to bit n makes pin n part of the multi-pin configuration. When one or more bits in the MPC-
MASK register is set, writing any of the PINnCTRL registers will update only the PINnCTRL
registers matching the mask in the MPCMASK register for that port. The MPCMASK register is
automatically cleared after any PINnCTRL register is written.
• Bit 7:4 – VP1MAP: Virtual Port 1 Mapping
These bits decide which ports should be mapped to Virtual Port 1. The registers DIR, OUT, IN,
and INTFLAGS will be mapped. Accessing the virtual port registers is equal to accessing the
actual port registers. See
• Bit 3:0 – VP0MAP: Virtual Port 0 Mapping
These bits decide which ports should be mapped to Virtual Port 0. The registers DIR, OUT, IN,
and INTFLAGS will be mapped. Accessing the virtual port registers is equal to accessing the
actual port registers. See
• Bit 7:4 – VP3MAP: Virtual Port 3 Mapping
These bits decide which ports should be mapped to Virtual Port 3. The registers DIR, OUT, IN,
and INTFLAGS will be mapped. Accessing the virtual port registers is equal to accessing the
actual port registers. See
Bit
+0x00
Read/Write
Initial Value
Bit
+0x02
Read/Write
Initial Value
Bit
+0x03
Read/Write
Initial Value
R/W
R/W
R/W
7
0
7
0
7
0
R/W
R/W
R/W
6
0
6
0
6
0
VP1MAP[3:0]
VP3MAP[3:0]
Table 12-6
Table 12-6
Table 12-6
R/W
R/W
R/W
5
0
5
0
5
0
for configuration.
for configuration.
for configuration.
R/W
R/W
R/W
4
0
4
0
4
0
MPCMASK[7:0]
R/W
R/W
R/W
3
0
3
0
3
0
Atmel AVR XMEGA B
R/W
R/W
R/W
2
0
2
0
2
0
VP0MAP[3:0]
VP2MAP[3:0]
R/W
R/W
R/W
1
0
1
0
1
0
R/W
R/W
R/W
0
0
0
0
0
0
MPCMASK
VPCTRLA
VPCTRLB
144