ATxmega128B1 Atmel Corporation, ATxmega128B1 Datasheet - Page 262

• Manufacturer Part Number: ATxmega128B1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 53
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 10
• Input Capture Channels: 10
• Pwm Channels: 10
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

20. SPI – Serial Peripheral Interface
20.1
20.2
8291A–AVR–10/11
Features
Overview
•
•
•
•
•
•
•
•
The Serial Peripheral Interface (SPI) is a high-speed synchronous data transfer interface using
three or four pins. It allows fast communication between an XMEGA device and peripheral
devices or between several microcontrollers. The SPI supports full-duplex communication.
A device connected to the bus must act as a master or slave.The master initiates and controls all
data transactions. The interconnection between master and slave devices with SPI is shown in
Figure 20-1 on page
tor. The SPI master initiates the communication cycle by pulling the slave select (SS) signal low
for the desired slave. Master and slave prepare the data to be sent in their respective shift regis-
ters, and the master generates the required clock pulses on the SCK line to interchange data.
Data are always shifted from master to slave on the master output, slave input (MOSI) line, and
from slave to master on the master input, slave output (MISO) line. After each data packet, the
master can synchronize the slave by pulling the SS line high.
Figure 20-1. SPI master-slave interconnection.
The SPI module is single buffered in the transmit direction and double buffered in the receive
direction. This means that bytes to be transmitted cannot be written to the SPI DATA register
before the entire shift cycle is completed. When receiving data, a received character must be
read from the DATA register before the next character has been completely shifted in. Other-
wise, the first byte will be lost.
In SPI slave mode, the control logic will sample the incoming signal on the SCK pin. To ensure
correct sampling of this clock signal, the minimum low and high periods must each be longer
than two CPU clock cycles.
Full-duplex, three-wire synchronous data transfer
Master or slave operation
Lsb first or msb first data transfer
Eight programmable bit rates
Interrupt flag at the end of transmission
Write collision flag to indicate data collision
Wake up from idle sleep mode
Double speed master mode
262. The system consists of two shift registers and a master clock genera-
Atmel AVR XMEGA B
SHIFT
ENABLE
262