ATxmega128B1 Atmel Corporation, ATxmega128B1 Datasheet - Page 247

• Manufacturer Part Number: ATxmega128B1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 53
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 10
• Input Capture Channels: 10
• Pwm Channels: 10
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 19-13. TWI slave operation.
19.6.1
19.6.1.1
19.6.1.2
8291A–AVR–10/11
S1
S2
SW
Sn
Driver software
The master provides data
on the bus
Slave provides data on
the bus
Diagram connections
Receiving Address Packets
S3
S
Case S1: Address packet accepted - Direction bit set
Case S2: Address packet accepted - Direction bit cleared
ADDRESS
The number of interrupts generated is kept to a minimum by automatic handling of most condi-
tions. Quick command can be enabled to auto-trigger operations and reduce software
complexity.
Promiscuous mode can be enabled to allow the slave to respond to all received addresses.
When the TWI slave is properly configured, it will wait for a START condition to be detected.
When this happens, the successive address byte will be received and checked by the address
match logic, and the slave will ACK a correct address. If the received address is not a match, the
slave will not acknowledge the address, and will wait for a new START condition.
The slave address/stop interrupt flag is set when a START condition succeeded by a valid
address byte is detected. A general call address will also set the interrupt flag.
A START condition immediately followed by a STOP condition is an illegal operation, and the
bus error flag is set.
The R/W direction flag reflects the direction bit received with the address. This can be read by
software to determine the type of operation currently in progress.
Depending on the R/W direction bit and bus condition, one of four distinct cases (S1 to S4)
arises following the address packet. The different cases must be handled in software.
If the R/W direction flag is set, this indicates a master read operation. The SCL line is forced low
by the slave, stretching the bus clock. If ACK is sent by the slave, the slave hardware will set the
data interrupt flag indicating data is needed for transmit. Data, repeated START, or STOP can
be received after this. If NACK is sent by the slave, the slave will wait for a new START condition
and address match.
If the R/W direction flag is cleared, this indicates a master write operation. The SCL line is forced
low, stretching the bus clock. If ACK is sent by the slave, the slave will wait for data to be
Interrupt on STOP
Condition Enabled
SLAVE ADDRESS INTERRUPT
Collision
(SMBus)
W
R
SW
SW
SW
SW
Release
Hold
A/A
A
A
A
S1
S1
S1
Sr
P
S2
S3
DATA
Atmel AVR XMEGA B
SLAVE DATA INTERRUPT
SW
SW
A/A
Sr
P
S2
S3
DATA
A/A
247