ATxmega128B1 Atmel Corporation, ATxmega128B1 Datasheet - Page 267

• Manufacturer Part Number: ATxmega128B1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 53
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 10
• Input Capture Channels: 10
• Pwm Channels: 10
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

20.7.4
20.8
20.9
Table 20-4.
8291A–AVR–10/11
Address
+0x00
+0x01
+0x02
+0x03
Offset
0x00
Register Summary
Interrupt vector Summary
DATA – Data register
Name
SPI interrupt vector and its offset word address.
INTCTRL
STATUS
CTRL
DATA
SPI_vect
• Bit 6 – WRCOL: Write Collision Flag
The WRCOL flag is set if the DATA register is written during a data transfer. This flag is cleared
by first reading the STATUS register when WRCOL is set, and then accessing the DATA
register.
• Bit 5:0 – Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
The DATA register is used for sending and receiving data. Writing to the register initiates the
data transmission, and the byte written to the register will be shifted out on the SPI output line.
Reading the register causes the shift register receive buffer to be read, returning the last byte
successfully received.
Source
CLK2X
Bit 7
Bit
+0x03
Read/Write
Initial Value
IF
–
ENABLE
WRCOL
Bit 6
R/W
–
7
0
Interrupt Description
SPI interrupt vector
R/W
Bit 5
DORD
6
0
–
–
R/W
MASTER
5
0
Bit 4
–
–
DATA[7:0]
R/W
4
0
Bit 3
DATA[7:0]
–
–
MODE[1:0]
R/W
3
0
Atmel AVR XMEGA B
Bit 2
–
–
R/W
2
0
Bit 1
–
PRESCALER[1:0]
INTLVL[1:0]
R/W
1
0
Bit 0
–
R/W
0
0
Page
DATA
265
266
266
267
267