ATxmega128B1 Atmel Corporation, ATxmega128B1 Datasheet - Page 205

• Manufacturer Part Number: ATxmega128B1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 53
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 10
• Input Capture Channels: 10
• Pwm Channels: 10
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

17.3.2
17.3.3
8291A–AVR–10/11
STATUS – Status register
INTCTRL – Interrupt Control register
• Bit 7:1 – Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
• Bit 0 – SYNCBUSY: Synchronization Busy Flag
This flag is set when the CNT, CTRL, PER, or COMP register is busy synchronizing between the
RTC clock and system clock domains. THis flag is automatically cleared when the synchronisa-
tion is complete
• Bit 7:4 – Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
• Bit 3:2 – COMPINTLVL[1:0]: Compare Match Interrupt Enable
These bits enable the RTC compare match interrupt and select the interrupt level, as described
in
rupt will trigger when COMPIF in the INTFLAGS register is set.
• Bit 1:0 – OVFINTLVL[1:0]: Overflow Interrupt Enable
These bits enable the RTC overflow interrupt and select the interrupt level, as described in
”Interrupts and Programmable Multilevel Interrupt Controller” on page
will trigger when OVFIF in the INTFLAGS register is set.
Bit
+0x01
Read/Write
Initial Value
Bit
+0x02
Read/Write
Initial Value
”Interrupts and Programmable Multilevel Interrupt Controller” on page
7
–
R
0
7
–
R
0
R
6
–
0
6
–
R
0
R
5
–
0
R
5
–
0
R
4
–
0
R
4
–
0
R/W
R
3
–
0
COMPINTLVL[1:0]
3
0
Atmel AVR XMEGA B
R/W
R
2
–
0
2
0
133. The enabled interrupt
R
R/W
1
–
0
1
OVFINTLVL[1:0]
0
133. The enabled inter-
SYNCBUSY
R/W
R
0
0
0
0
INTCTRL
STATUS
205