ATxmega128B1 Atmel Corporation, ATxmega128B1 Datasheet - Page 357

• Manufacturer Part Number: ATxmega128B1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 53
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 10
• Input Capture Channels: 10
• Pwm Channels: 10
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

26.8.7
26.8.8
8291A–AVR–10/11
CURRCTRL – Current Source Control register
CURRCALIB – Current Source Calibration register
This flag is automatically cleared when the analog comparator window interrupt vector is exe-
cuted. The flag can also be cleared by writing a one to its bit location.
• Bit 1 – AC1IF: Analog Comparator 1 Interrupt Flag
This is the interrupt flag for AC1. AC1IF is set according to the INTMODE setting in the corre-
sponding
This flag is automatically cleared when the analog comparator 1 interrupt vector is executed.
The flag can also be cleared by writing a one to its bit location.
• Bit 0 – AC0IF: Analog Comparator 0 Interrupt Flag
This is the interrupt flag for AC0. AC0IF is set according to the INTMODE setting in the corre-
sponding
This flag is automatically cleared when the analog comparator 0 interrupt vector is executed.
The flag can also be cleared by writing a one to its bit location.
• Bit 7 – CURRENT: Current Source Enable
Setting this bit to one will enable the constant current source.
• Bit 6 – CURRMODE: Current Mode
Setting this bit to one will combine the two analog comparator current sources in order to double
the output current for each analog comparator.
• Bit 5:2 – Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
• Bit 1 – AC1CURR: AC1 Current Source Output Enable
Setting this bit to one will enable the constant current source output on the pin selected by MUX-
NEG in AC1MUXTRL.
• Bit 0 – AC0CURR: AC0 Current Source Output Enable
Setting this bit to one will enable the constant current source output on the pin selected by MUX-
NEG in AC0MUXTRL.
Bit
+0x09
Read/Write
Initial Value
Bit
+0x08
Read/Write
Initial Value
”ACnCTRL – Analog Comparator n Control register” on page
”ACnCTRL – Analog Comparator n Control register” on page
CURRENT
R/W
R
7
–
0
7
0
CURRMODE
R
6
–
0
R/W
6
0
R
5
–
0
5
–
R
0
4
–
R
0
4
–
R
0
R/W
3
0
R
3
–
0
Atmel AVR XMEGA B
R/W
2
0
R
2
–
0
CALIB[3:0]
AC1CURR
R/W
R/W
1
0
1
0
353.
353.
AC0CURR
R/W
R/W
0
0
0
0
CURRCALIB
CURRCTRL
357