ATxmega128B1 Atmel Corporation, ATxmega128B1 Datasheet - Page 56

• Manufacturer Part Number: ATxmega128B1
• Manufacturer: Atmel Corporation

Specifications of ATxmega128B1

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 53
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 10
• Input Capture Channels: 10
• Pwm Channels: 10
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

5.13.4
5.14
5.14.1
8291A–AVR–10/11
Register Description – DMA Channel
TEMP – Temporary Register
CTRLA – Control Register A
• Bit 7:0 – TEMP[7:0]: Temporary Register
This register is used when reading 16-bit registers in the DMA controller. Byte 1 of the 16-bit reg-
ister is stored here when it is written by the CPU. Byte 1 of the 16-bit register is stored when byte
0 is read by the CPU. This register can also be read and written from the user software.
Reading and writing 16-bit registers requires special attention. For details, refer to
16-bit Registers” on page
• Bit 7 – CHEN: Enable
Setting this bit enables the DMA channel. This bit is automatically cleared when the transaction
is completed. If the DMA channel is enabled and this bit is written to zero, the CHEN bit is not
cleared until the internal transfer buffer is empty and the DMA transfer is aborted.
• Bit 6 – CHRST: Software Reset
Setting this bit will reset the DMA channel. It can only be set when the DMA channel is disabled
(CHEN = 0). Writing a one to this bit will be gnored as long as the channel is enabled (CHEN=1).
This bit is automatically cleared when reset is completed.
• Bit 5 – REPEAT: Repeat Mode
Setting this bit enables the repeat mode. In repeat mode, this bit is cleared by hardware at the
beginning of the last block transfer. The REPCNT register should be configured before setting
the REPEAT bit.
• Bit 4 – TRFREQ: Transfer Request
Setting this bit requests a data transfer on the DMA channel. This bit is automatically cleared at
the beginning of the data transfer. Writing this bit does not have any effect unless the channel is
enabled.
• Bit 3 – Reserved
This bit is unused and reserved for future use. For compatibility with future devices, always write
this bit to zero when this register is written.
Bit
+0x00
Read/Write
Initial Value
Bit
+0x06
Read/Write
Initial Value
CHEN
R/W
R/W
7
0
7
0
CHRST
R/W
R/W
6
0
6
0
12.
REPEAT
R/W
R/W
5
0
5
0
TRFREQ
R/W
R/W
4
0
4
0
TEMP[7:0]
R/W
3
0
R
3
–
0
Atmel AVR XMEGA B
SINGLE
R/W
R/W
2
0
2
0
R/W
R/W
1
0
1
BURSTLEN[1:0]
0
R/W
R/W
0
0
0
0
”Accessing
CTRLA
TEMP
56