LPC1112FHN33/203,5 NXP Semiconductors, LPC1112FHN33/203,5 Datasheet - Page 5

• Manufacturer Part Number: LPC1112FHN33/203,5
• Description: ARM Microcontrollers - MCU Cortex-M0 16kB flash up to 4 kB SRAM
• Manufacturer: NXP Semiconductors

Specifications of LPC1112FHN33/203,5

• Rohs: yes
• Core: ARM Cortex M0
• Processor Series: LPC1112
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 16 KB
• Data Ram Size: 4 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 1.8 V to 3.6 V
• Operating Temperature Range: - 65 C to + 150 C
• Package / Case: HVQFN-33
• Mounting Style: SMD/SMT
• Factory Pack Quantity: 260

NXP Semiconductors
1.2 Features
UM10398
User manual
•
•
•
•
•
•
System:
– ARM Cortex-M0 processor, running at frequencies of up to 50 MHz.
– ARM Cortex-M0 built-in Nested Vectored Interrupt Controller (NVIC).
– Serial Wire Debug.
– System tick timer.
Memory:
– On-chip flash programming memory for LPC1100, LPC1100L, and LPC1100C
– On-chip flash programming memory for LPC1100XL series: 8 kB (LPC1111), 16 kB
– 8 kB, 4 kB, 2 kB, or 1 kB SRAM.
– In-System Programming (ISP) and In-Application Programming (IAP) via on-chip
– LPC1100XL series only: page erase IAP command.
Digital peripherals:
– Up to 42 General Purpose I/O (GPIO) pins with configurable pull-up/pull-down
– GPIO pins can be used as edge and level sensitive interrupt sources.
– High-current output driver (20 mA) on one pin.
– High-current sink drivers (20 mA) on two I
– Four general purpose timers/counters with a total of four capture inputs and up to
– Programmable WatchDog Timer (WDT).
Analog peripherals:
– 10-bit ADC with input multiplexing among up to 8 pins.
Serial interfaces:
– UART with fractional baud rate generation, internal FIFO, and RS-485 support.
– Two SPI controllers with SSP features and with FIFO and multi-protocol
– I
– C_CAN controller (LPC11Cxx only). On-chip CAN and CANopen drivers included.
– On-chip, high-speed CAN transceiver (parts LPC11C22/C24 only).
Clock generation:
– 12 MHz internal RC oscillator trimmed to 1% accuracy that can optionally be used
– Crystal oscillator with an operating range of 1 MHz to 25 MHz.
series: 32 kB (LPC1114/LPC11C14), 24 kB (LPC1113), 16 kB
(LPC1112/LPC11C12), or 8 kB (LPC1111), 4kB (LPC1110) .
(LPC1112), 24 kB (LPC1113), 32 kB (LPC1114/203/303), 48 kB (LPC1114/323),
56 kB (LPC1114/333), 64 kB (LPC1115).
bootloader software.
resistors. Number of GPIO pins is reduced for smaller packages and
LPC11C22/C24.
13 match outputs.
capabilities (second SPI on LQFP48 packages only).
data rate of 1 Mbit/s with multiple address recognition and monitor mode.
as a system clock.
2
C-bus interface supporting full I
All information provided in this document is subject to legal disclaimers.
Rev. 12 — 24 September 2012
Chapter 1: LPC111x/LPC11Cxx Introductory information
2
C-bus specification and Fast-mode Plus with a
2
C-bus pins in Fast-mode Plus.
UM10398
© NXP B.V. 2012. All rights reserved.
5 of 538