UPD78F1152AGC-GAD-AX Renesas Electronics America, UPD78F1152AGC-GAD-AX Datasheet - Page 384

• Manufacturer Part Number: UPD78F1152AGC-GAD-AX
• Description: MCU 16BIT 78K0R/KX3 80-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Kx3r

Specifications of UPD78F1152AGC-GAD-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 65
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

12.4 Operation stop mode
P12/SO00/TxD0,
P143/SI20/SDA20/RxD2, or P144/SO20/TxD2 pin can be used as ordinary port pins in this mode.
12.4.1 Stopping the operation by units
is not used is stopped in order to reduce the power consumption and noise.
382
Each serial interface of serial array unit has the operation stop mode.
In this mode, serial communication cannot be executed, thus reducing the power consumption.
In addition, the P02/SO10/TxD1, P03/SI10/SDA10/RxD1, P04/SCK10/SCL10, P10/SCK00, P11/SI00/RxD0,
The stopping of the operation by units is set by using peripheral enable register 0 (PER0).
PER0 is used to enable or disable use of each peripheral hardware macro. Clock supply to a hardware macro that
To stop the operation of serial array unit 0, set bit 2 (SAU0EN) to 0.
To stop the operation of serial array unit 1, set bit 3 (SAU1EN) to 0.
PER0
Figure 12-22. Peripheral Enable Register 0 (PER0) Setting When Stopping the Operation by Units
Cautions 1. If SAUmEN = 0, writing to a control register of serial array unit m is ignored, and, even if
Remark
(a) Peripheral enable register 0 (PER0) … Set only the bit of SAUm to be stopped to 0.
RTCEN
×
7
2. Be sure to clear bit 1 of the PER0 register to 0.
m: Unit number (m = 0, 1),
×: Bits not used with serial array units (depending on the settings of other peripheral functions)
0/1: Set to 0 or 1 depending on the usage of the user
P13/TxD3,
the register is read, only the default value is read (except for input switch control register
(ISC), noise filter enable register (NFEN0), port input mode registers (PIM0, PIM4, PIM14),
port output mode registers (POM0, POM4, POM14), port mode registers (PM0, PM1, PM4,
PM14), and port registers (P0, P1, P4, P14)).
DACEN
×
6
Control of SAUm input clock
0: Stops supply of input clock
1: Supplies input clock
P14/RxD3,
ADCEN
CHAPTER 12 SERIAL ARRAY UNIT
×
5
User’s Manual U17893EJ8V0UD
: Setting disabled (fixed by hardware)
P43/SCK01,
IIC0EN
4
×
SAU1EN
0/1
3
P44/SI01,
SAU0EN
0/1
2
P45/SO01,
0
1
P142/SCK20/SCL20,
TAU0EN
0
×