UPD78F1152AGC-GAD-AX Renesas Electronics America, UPD78F1152AGC-GAD-AX Datasheet - Page 689

• Manufacturer Part Number: UPD78F1152AGC-GAD-AX
• Description: MCU 16BIT 78K0R/KX3 80-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Kx3r

Specifications of UPD78F1152AGC-GAD-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 65
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

24.4.4 Port pins
same status as that immediately after reset. If external devices connected to the ports do not recognize the port
status immediately after reset, the port pin must be connected to V
24.4.5 REGC pin
However, when using the STOP mode that has been entered since operation of the internal high-speed oscillation
clock and external main system clock, 0.47
since it is used to stabilize internal voltage.
24.4.6 X1 and X2 pins
24.4.7 Power supply
programmer, and the V
flash memory programmer to use the power monitor function with the flash memory programmer.
mode.
24.5 Registers that Control Flash Memory
(1) Background event control register (BECTL)
Address: FFFBEH
When the flash memory programming mode is set, all the pins not used for flash memory programming enter the
Connect the REGC pin to GND via a capacitor (0.47 to 1
Connect X1 and X2 in the same status as in the normal operation mode.
Remark In the flash memory programming mode, the internal high-speed oscillation clock (f
To use the supply voltage output of the flash memory programmer, connect the V
To use the on-board supply voltage, connect in compliance with the normal operation mode.
However, when using the on-board supply voltage, be sure to connect the V
Supply the same other power supplies (EV
Symbol
BECTL
Even if the FLMD0 pin is not controlled externally, it can be controlled by software with the BECTL register to set
the self-programming mode.
However, depending on the processing of the FLMD0 pin, it may not be possible to set the self-programming
mode by software. When using BECTL, leaving the FLMD0 pin open is recommended. When pulling it down
externally, use a resistor with a resistance of 100 kΩ or more. In addition, in the normal operation mode, use
BECTL with the pull down selection. In the self-programming mode, the setting is switched to pull up in the self-
programming library.
The BECTL register is set by a 1-bit or 8-bit memory manipulation instruction.
Reset input sets this register to 00H.
FLMDPUP
FLMDPUP
<7>
0
1
After reset: 00H
Figure 24-6. Format of Background Event Control Register (BECTL)
SS
pin to GND of the flash memory programmer.
Selects pull-down
Selects pull-up
6
0
R/W
CHAPTER 24 FLASH MEMORY
5
0
μ
User’s Manual U17893EJ8V0UD
DD
F is recommended. Also, use a capacitor with good characteristics,
, EV
SS
, AV
4
0
Software control of FLMD0 pin
REF0
μ
, AV
F) in the same manner as during normal operation.
DD
REF1
or V
3
0
, and AV
SS
via a resistor.
DD
SS
and V
) as those in the normal operation
DD
2
0
pin to V
SS
pins to V
DD
IH
) is used.
1
0
of the flash memory
DD
and GND of the
0
0
687