HD6417720BP133BV Renesas Electronics America, HD6417720BP133BV Datasheet - Page 464
HD6417720BP133BV
Manufacturer Part Number
HD6417720BP133BV
Description
SH3-DSP, WITH USB AND LCDC, PB-F
Manufacturer
Renesas Electronics America
Series
SuperH® SH7700r
Datasheet
1.R8A77210C133BAV.pdf
(1478 pages)
Specifications of HD6417720BP133BV
Core Processor
SH-3 DSP
Core Size
32-Bit
Speed
133MHz
Connectivity
FIFO, I²C, IrDA, MMC, SCI, SD, SIO, SIM, USB
Peripherals
DMA, LCD, POR, WDT
Number Of I /o
117
Program Memory Type
ROMless
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
1.4 V ~ 1.6 V
Data Converters
A/D 4x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 75°C
Package / Case
256-BGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Program Memory Size
-
- Current page: 464 of 1478
- Download datasheet (10Mb)
Section 9 Bus State Controller (BSC)
9.6
(1)
The bus state controller (BSC) can be initialized completely only at power-on reset. At power-on
reset, all signals are negated and output buffers are turned off regardless of the bus cycle state. All
control registers are initialized. In standby, sleep, and manual reset, control registers of the bus
state controller are not initialized. At manual reset, the current bus cycle being executed is
completed and then the access wait state is entered. If a 16-byte transfer is performed by a cache
or if another LSI on-chip bus master module is executed when a manual reset occurs, the current
access is cancelled in longword units because the access request is cancelled by the bus master at
manual reset. If a manual reset is requested during cache fill operations, the contents of the cache
cannot be guaranteed. Since the RTCNT continues counting up during manual reset signal
assertion, a refresh request occurs to initiate the refresh cycle. In addition, a bus arbitration request
by the BREQ signal can be accepted during manual reset signal assertion.
Some flash memories may specify a minimum time from reset release to the first access. To
ensure this minimum time, the bus state controller supports a 5-bit counter (RWTCNT). At power-
on reset, the RWTCNT is cleared to 0. After power-on reset, RWTCNT is counted up
synchronously together with CKIO and an external access will not be generated until RWTCNT is
counted up to H
(2)
There are three types of LSI internal buses: a cache bus, internal bus, and peripheral bus. The CPU
and cache memory are connected to the cache bus. Internal bus masters other than the CPU and
bus state controller are connected to the internal bus. Low-speed peripheral modules are connected
to the peripheral bus. Internal memories other than the cache memory and debugging modules
such as a UBC and AUD are connected bidirectionally to the cache bus and internal bus. Access
from the cache bus to the internal bus is enabled but access from the internal bus to the cache bus
is disabled. This gives rise to the following problems.
Internal bus masters such as DMAC other than the CPU can access on-chip memory other than the
cache memory but cannot access the cache memory. If an on-chip bus master other than the CPU
writes data to an external memory other than the cache, the contents of the external memory may
differ from that of the cache memory. To prevent this problem, if the external memory whose
contents is cached is written by an on-chip bus master other than the CPU, the corresponding
cache memory should be purged by software.
If the CPU initiates read access for the cache, the cache is searched. If the cache stores data, the
CPU latches the data and completes the read access. If the cache does not store data, the CPU
Page 404 of 1414
Reset
Access from the Site of the LSI Internal Bus Master
Usage Notes
′
001F. At manual reset, RWTCNT is not cleared.
SH7720 Group, SH7721 Group
R01UH0083EJ0400 Rev. 4.00
Sep 21, 2010
Related parts for HD6417720BP133BV
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: