LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 282

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
UM10237_4
User manual
4.1 Programmable parameters
4.2 Hardware cursor support
The following key display and controller parameters can be programmed:
The hardware cursor feature reduces software overhead associated with maintaining a
cursor image in the LCD frame buffer.
Without this feature, software needed to:
In addition, the LCD driver had to check whether the graphics operation had overwritten
the cursor, and correct it. With a cursor size of 64x64 and 24-bit color, each cursor move
involved reading and writing approximately 75KB of data.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
256 entry, 16-bit palette RAM, arranged as a 128x32-bit RAM.
Frame, line, and pixel clock signals.
AC bias signal for STN, data enable signal for TFT panels.
Supports little and big-endian, and Windows CE data formats.
LCD panel clock may be generated from the peripheral clock, or from a clock input
pin.
Horizontal front and back porch
Horizontal synchronization pulse width
Number of pixels per line
Vertical front and back porch
Vertical synchronization pulse width
Number of lines per panel
Number of pixel clocks per line
Hardware cursor control.
Signal polarity, active HIGH or LOW
AC panel bias
Panel clock frequency
Bits-per-pixel
Display type: STN monochrome, STN color, or TFT
STN 4 or 8-bit interface mode
STN dual or single panel mode
Little-endian, big-endian, or Windows CE mode
Interrupt generation event
Save an image of the area under the next cursor position.
Update the area with the cursor image.
Repair the last cursor position with a previously saved image.
Rev. 04 — 26 August 2009
Chapter 12: LPC24XX LCD controller
UM10237
© NXP B.V. 2009. All rights reserved.
282 of 792