LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 433

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
UM10237_4
User manual
Table 387. UARTn Line Status Register (U0LSR - address 0xE000 C014,
Bit Symbol
2
3
4
5
6
7
Parity Error
Framing Error
Break
Interrupt
Transmitter
Holding
Register
Empty
Transmitter
Empty
(TEMT)
Error in RX
FIFO
(RXFE)
(PE)
(FE)
(BI)
(THRE))
U2LSR - 0xE007 8014, U3LSR - 0xE007 C014, Read Only) bit description
Value Description
0
1
0
1
0
1
0
1
0
1
0
1
Rev. 04 — 26 August 2009
When the parity bit of a received character is in the wrong
state, a parity error occurs. An UnLSR read clears UnLSR[2].
Time of parity error detection is dependent on UnFCR[0].
Note: A parity error is associated with the character at the top
of the UARTn RBR FIFO.
Parity error status is inactive.
Parity error status is active.
When the stop bit of a received character is a logic 0, a
framing error occurs. An UnLSR read clears UnLSR[3]. The
time of the framing error detection is dependent on UnFCR0.
Upon detection of a framing error, the Rx will attempt to
resynchronize to the data and assume that the bad stop bit is
actually an early start bit. However, it cannot be assumed that
the next received byte will be correct even if there is no
Framing Error.
Note: A framing error is associated with the character at the
top of the UARTn RBR FIFO.
Framing error status is inactive.
Framing error status is active.
When RXDn is held in the spacing state (all 0’s) for one full
character transmission (start, data, parity, stop), a break
interrupt occurs. Once the break condition has been detected,
the receiver goes idle until RXDn goes to marking state (all
1’s). An UnLSR read clears this status bit. The time of break
detection is dependent on UnFCR[0].
Note: The break interrupt is associated with the character at
the top of the UARTn RBR FIFO.
Break interrupt status is inactive.
Break interrupt status is active.
THRE is set immediately upon detection of an empty UARTn
THR and is cleared on a UnTHR write.
UnTHR contains valid data.
UnTHR is empty.
TEMT is set when both UnTHR and UnTSR are empty; TEMT
is cleared when either the UnTSR or the UnTHR contain valid
data.
UnTHR and/or the UnTSR contains valid data.
UnTHR and the UnTSR are empty.
UnLSR[7] is set when a character with a Rx error such as
framing error, parity error or break interrupt, is loaded into the
UnRBR. This bit is cleared when the UnLSR register is read
and there are no subsequent errors in the UARTn FIFO.
UnRBR contains no UARTn RX errors or UnFCR[0]=0.
UARTn RBR contains at least one UARTn RX error.
Chapter 16: LPC24XX UART0/2/3
UM10237
© NXP B.V. 2009. All rights reserved.
433 of 792
Reset
Value
0
0
0
1
1
0