LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 579

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
UM10237_4
User manual
7.2 Address Register I2ADDR
7.3 Comparator
7.4 Shift register I2DAT
7.5 Arbitration and synchronization logic
This register may be loaded with the 7 bit slave address (7 most significant bits) to which
the I
(GC) is used to enable general call address (0x00) recognition.
The comparator compares the received 7 bit slave address with its own slave address (7
most significant bits in I2ADR). It also compares the first received 8 bit byte with the
general call address (0x00). If an equality is found, the appropriate status bits are set and
an interrupt is requested.
This 8 bit register contains a byte of serial data to be transmitted or a byte which has just
been received. Data in I2DAT is always shifted from right to left; the first bit to be
transmitted is the MSB (bit 7) and, after a byte has been received, the first bit of received
data is located at the MSB of I2DAT. While data is being shifted out, data on the bus is
simultaneously being shifted in; I2DAT always contains the last byte present on the bus.
Thus, in the event of lost arbitration, the transition from master transmitter to slave
receiver is made with the correct data in I2DAT.
In the master transmitter mode, the arbitration logic checks that every transmitted logic 1
actually appears as a logic 1 on the I
1 and pulls the SDA line low, arbitration is lost, and the I
from master transmitter to slave receiver. The I
pulses (on SCL) until transmission of the current serial byte is complete.
Arbitration may also be lost in the master receiver mode. Loss of arbitration in this mode
can only occur while the I
Arbitration is lost when another device on the bus pulls this signal LOW. Since this can
occur only at the end of a serial byte, the I
Figure 22–118
Fig 118. Arbitration procedure
2
C block will respond when programmed as a slave transmitter or receiver. The LSB
(1) A device transmits serial data.
(2) Another device overrules a logic 1 (dotted line), transmitted by this I
(3) This I
line low. Arbitration is lost, and this I
transmitted. This I
the new master once it has won arbitration.
SDA line
SCL line
2
C is in Slave Receiver mode but still generates clock pulses until the current byte has been
shows the arbitration procedure.
Rev. 04 — 26 August 2009
2
C will not generate clock pulses for the next byte. Data on SDA originates from
2
C block is returning a “not acknowledge: (logic 1) to the bus.
(1)
1
(1)
2
2
C bus. If another device on the bus overrules a logic
2
C enters Slave Receiver mode.
(2)
3
2
Chapter 22: LPC24XX I
C block generates no further clock pulses.
2
C block will continue to output clock
4
2
C block immediately changes
(3)
2
C master, by pulling the SDA
8
2
C interfaces I
UM10237
© NXP B.V. 2009. All rights reserved.
ACK
9
579 of 792
2
C0/1/2