LPC2468FET208,551 NXP Semiconductors, LPC2468FET208,551 Datasheet - Page 690

• Manufacturer Part Number: LPC2468FET208,551
• Description: IC ARM7 MCU FLASH 512K 208TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2468FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2S/ISP/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 6
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, IRD-LPC2468-DEV, SAB-TFBGA208, KSK-LPC2468-PL
• Development Tools By Supplier: OM10100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1025 - KIT DEV IND REF DESIGN LPC2468622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4358 - DISPLAY QVGA TFT FOR OM10100568-4309 - BOARD EXTENSION LPCSTICK568-4308 - EVAL LPC-STICK WITH LPC2468MCB2400U - BOARD EVAL MCB2400 + ULINK2MCB2400 - BOARD EVAL FOR NXP LPC246X SER622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4262; 935283234551; LPC2468FET208-S

NXP Semiconductors
10. IAP commands
UM10237_4
User manual
9.14 ISP Return Codes
Table 619. ISP Return Codes Summary
For in application programming the IAP routine should be called with a word pointer in
register r0 pointing to memory (RAM) containing command code and parameters. Result
of the IAP command is returned in the result table pointed to by register r1. The user can
reuse the command table for result by passing the same pointer in registers r0 and r1. The
parameter table should be big enough to hold all the results in case if number of results
are more than number of parameters. Parameter passing is illustrated in the
Figure
command. The maximum number of parameters is 5, passed to the "Copy RAM to
Return
Code
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
30–140. The number of parameters and results vary according to the IAP
Mnemonic
CMD_SUCCESS
INVALID_COMMAND
SRC_ADDR_ERROR
DST_ADDR_ERROR
SRC_ADDR_NOT_MAPPED
DST_ADDR_NOT_MAPPED
COUNT_ERROR
INVALID_SECTOR
SECTOR_NOT_BLANK
SECTOR_NOT_PREPARED_FOR_
WRITE_OPERATION
COMPARE_ERROR
BUSY
PARAM_ERROR
ADDR_ERROR
ADDR_NOT_MAPPED
CMD_LOCKED
INVALID_CODE
INVALID_BAUD_RATE
INVALID_STOP_BIT
CODE_READ_PROTECTION_
ENABLED
Rev. 04 — 26 August 2009
Chapter 30: LPC24XX Flash memory programming firmware
Description
Command is executed successfully. Sent by ISP
Source address is not on word boundary.
Source address is not mapped in the memory map.
Source and destination data not equal.
handler only when command given by the host has
been completely and successfully executed.
Invalid command.
Destination address is not on a correct boundary.
Count value is taken in to consideration where
applicable.
Destination address is not mapped in the memory
map. Count value is taken in to consideration
where applicable.
Byte count is not multiple of 4 or is not a permitted
value.
Sector number is invalid or end sector number is
greater than start sector number.
Sector is not blank.
Command to prepare sector for write operation
was not executed.
Flash programming hardware interface is busy.
Insufficient number of parameters or invalid
parameter.
Address is not on word boundary.
Address is not mapped in the memory map. Count
value is taken in to consideration where applicable.
Command is locked.
Unlock code is invalid.
Invalid baud rate setting.
Invalid stop bit setting.
Code read protection enabled.
UM10237
© NXP B.V. 2009. All rights reserved.
690 of 792