DF2117VT20V Renesas Electronics America, DF2117VT20V Datasheet - Page 504

• Manufacturer Part Number: DF2117VT20V
• Description: MCU 16BIT FLASH 3V 160K 144-TQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2100r

Specifications of DF2117VT20V

• Core Processor: H8S/2600
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: FIFO, I²C, LPC, SCI, SmartCard
• Peripherals: POR, PWM, WDT
• Number Of I /o: 112
• Program Memory Size: 160KB (160K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 144-TQFP, 144-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

15.9
15.9.1
SCI operation can be disabled or enabled using the module stop control register. The initial setting
is for SCI operation to be halted. Register access is enabled by clearing module stop mode. For
details, see section 26, Power-Down Modes.
15.9.2
When framing error detection is performed, a break can be detected by reading the RxD pin value
directly. In a break, the input from the RxD pin becomes all 0s, and so the FER flag in SSR is set,
and the PER flag may also be set. Note that, since the SCI continues the receive operation even
after receiving a break, even if the FER flag is cleared to 0, it will be set to 1 again.
15.9.3
When the TE bit in SCR is 0, the TxD pin is used as an I/O port whose direction (input or output)
and level are determined by DR and DDR of the port. This can be used to set the TxD pin to mark
state (high level) or send a break during serial data transmission. To maintain the communication
line at mark state until TE is set to 1, set both DDR and DR to 1. Since the TE bit is cleared to 0 at
this point, the TxD pin becomes an I/O port, and 1 is output from the TxD pin. To send a break
during serial transmission, first set DDR to 1 and DR to 0, and then clear the TE bit to 0. When the
TE bit is cleared to 0, the transmitter is initialized regardless of the current transmission state, the
TxD pin becomes an I/O port, and 0 is output from the TxD pin.
15.9.4
Transmission cannot be started when a receive error flag (ORER, FER, or RER) is SSR is set to 1,
even if the TDRE flag in SSR is cleared to 0. Be sure to clear the receive error flags to 0 before
starting transmission. Note also that the receive error flags cannot be cleared to 0 even if the RE
bit in SCR is cleared to 0.
15.9.5
Data can be written to TDR irrespective of the TDRE flag status in SSR. However, if the new data
is written to TDR when the TDRE flag is 0, that is, when the previous data has not been
transferred to TSR yet, the previous data in TDR is lost. Be sure to write transmit data to TDR
after verifying that the TDRE flag is set to 1.
Rev. 2.00 Sep. 28, 2009 Page 462 of 994
REJ09B0452-0200
Usage Notes
Module Stop Mode Setting
Break Detection and Processing
Mark State and Break Sending
Receive Error Flags and Transmit Operations (Clocked Synchronous Mode Only)
Relation between Writing to TDR and TDRE Flag