MPC8533EVTAQGA Freescale Semiconductor, MPC8533EVTAQGA Datasheet - Page 1026

• Manufacturer Part Number: MPC8533EVTAQGA
• Description: MPU POWERQUICC 783-PBGA
• Manufacturer: Freescale Semiconductor

Specifications of MPC8533EVTAQGA

• Processor Type: MPC85xx PowerQUICC III 32-Bit
• Speed: 1.0GHz
• Voltage: 0.95 V ~ 1.05 V
• Mounting Type: Surface Mount
• Package / Case: 783-BBGA, FCBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -

PCI Bus Interface
PCI_AD[1:0] = 01 or PCI_AD[1:0] = 0b11 during the address phase of a local memory access. See
Section 17.4.2.8.2, “Target-Initiated Termination,”
For linear incrementing mode, the memory address is encoded/decoded using PCI_AD[31:2]. Thereafter,
the address is incremented by 4 bytes after each data phase completes until the transaction is terminated
or completed (a 4-byte data width per data phase is implied). Note that the two low-order bits on the
address bus are included in all parity calculations.
For cache wrap mode (PCI_AD[1:0] = 0b10) reads, the critical memory address is decoded using
PCI_AD[31:2]. The address is incremented by 4 bytes after each data phase completes until the end of the
cache line is reached. For cache-wrap reads, the address wraps to the beginning of the current cache line
and continues incrementing until the entire cache line (32 bytes) is read. The PCI controller does not
support cache-wrap write operations and executes a target disconnect after the data phase for the end of
the cache line completes for writes with PCI_AD[1:0] = 0b10. That is, the PCI controller does not wrap
back to the beginning of the cache line. Note that the two low-order bits on the address bus are included
in all parity calculations.
17.4.2.3.2
For PCI I/O accesses, 32 address signals (PCI_AD[31:0]) are used to provide a byte address. After a target
has claimed an I/O access, it must determine if it can complete the entire access as indicated by the byte
enable signals. If all the selected bytes are not in the address range of the target, the entire access cannot
complete. In this case, the target does not transfer any data and terminates the transaction with a
target-abort error. See
17.4.2.3.3
PCI supports two types of configuration accesses that use different formats for the PCI_AD[31:0] signals
during the address phase. The two low-order bits of the address indicate the format used for the
configuration address phase—type 0 (PCI_AD[1:0] = 0b00) or type 1 (PCI_AD[1:0] = 0b01). Both
address formats identify a specific device and a specific configuration register for that device. See
Section 17.4.2.11, “Configuration Cycles,”
17.4.2.4
The PCI_DEVSEL signal is driven by the target of the current transaction. PCI_DEVSEL indicates to the
other devices on the PCI bus that the target has decoded the address and claimed the transaction.
17-48
Device Selection
MPC8533E PowerQUICC III Integrated Host Processor Family Reference Manual, Rev. 1
I/O Space Addressing
Configuration Space Addressing
00
01
10
11
Section 17.4.2.8.2, “Target-Initiated Termination,”
PCI_AD[1:0]
Linear
Reserved
Cache Wrap
Reserved
Table 17-48. Supported Combinations of PCI_AD[1:0]
Read
for descriptions of the two formats.
TD
TD
√
√
Target
for more information on target disconnect conditions.
Write
TD
TD
TD
√
Read
—
—
—
√
Initiator
for more information.
Write
—
—
—
√
Freescale Semiconductor