HD6417641 RENESAS [Renesas Technology Corp], HD6417641 Datasheet - Page 306
HD6417641
Manufacturer Part Number
HD6417641
Description
Manufacturer
RENESAS [Renesas Technology Corp]
Datasheet
1.HD6417641.pdf
(1036 pages)
- Current page: 306 of 1036
- Download datasheet (5Mb)
Section 11 User Break Controller (UBC)
11.3
11.3.1
The flow from setting of break conditions to user break exception processing is described below:
1. The break addresses is set in the break address registers (BARA or BARB). The masked
2. When the break conditions are satisfied, the UBC sends a user break request to the CPU and
3. The appropriate condition match flags (SCMFCA, SCMFDA, SCMFCB, and SCMFDB) can
4. There is a chance that the break set in channel A and the break set in channel B occur around
5. When selecting the I bus as the break condition, note the following:
Rev. 4.00 Sep. 14, 2005 Page 256 of 982
REJ09B0023-0400
addresses are set in the break address mask registers (BAMRA or BAMRB). The break data is
set in the break data register (BDRB). The masked data is set in the break data mask register
(BDMRB). The bus break conditions are set in the break bus cycle registers (BBRA or
BBRB). Three groups of BBRA or BBRB (L bus cycle/I bus cycle select, instruction
fetch/data access select, and read/write select) are each set. No user break will be generated if
even one of these groups is set with 00. The respective conditions are set in the bits of the
break control register (BRCR). Make sure to set all registers related to breaks before setting
BBRA or BBRB.
sets the L bus condition match flag (SCMFCA or SCMFCB) and the I bus condition match
flag (SCMFDA or SCMFDB) for the appropriate channel. When the X/Y memory bus is
specified for channel B, SCMFCB is used for the condition match flag.
be used to check if the set conditions match or not. The matching of the conditions sets flags,
but they are not reset. 0 must first be written to them before they can be used again.
the same time. In this case, there will be only one break request to the CPU, but these two
break channel match flags could be both set.
Several bus masters, including the CPU and DMAC, are connected to the I bus. The UBC
Physical addresses are used for the I bus. Set a physical address in break address registers
For data access cycles issued on the L bus by the CPU, if their logical addresses are not to
For instruction fetch cycles issued on the L bus by the CPU, even though their logical
monitors bus cycles generated by all bus masters, and determines the condition match.
(BARA and BARB). The upper three bits of logical addresses in the P0 to P3 area issued
by the CPU on the L bus are masked (to 0) before they are placed on the I bus. The upper
three bits of the source and destination addresses set in the DMAC are masked in the same
way. However, logical addresses in the P4 area are output unchanged on the I bus.
be cached, they are issued with the data size specified on the L bus.
addresses are not to be cached, they are issued in longwords and their addresses are
rounded to match longword boundaries.
Operation
Flow of the User Break Operation
Related parts for HD6417641
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Renesas Technology Corp [Renesas 32-Bit RISC Microcomputer Super RISC engine Family/SH7700 Series]
Manufacturer:
Renesas Electronics Corporation.
Datasheet:
Part Number:
Description:
Renesas 32-Bit RISC Microcomputer Super RISC engine Family/SH7700 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer Renesas H8S Family/H8S/2100 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas MCU
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
RENESAS MCU
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
RENESAS MCU
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
RENESAS MCU
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer H8S Family / H8S/2200 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer H8S Family H8S-2300 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer H8S Family/H8S/2300 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer H8S Family/H8S/2300 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 16-Bit Single-Chip Microcomputer H8 Family/H8/300H Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 32-Bit Single-Chip RISC Microprocessor SuperH RISC engine Family/SH7040 Series(CPU Core SH-2)
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 32-Bit RISC Microcomputer SuperHTM RISC engine Family / SH7700 Series
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet:
Part Number:
Description:
Renesas 32-Bit RISC Microcomputer
Manufacturer:
RENESAS [Renesas Technology Corp]
Datasheet: