M3087BFLBGP#U5 Renesas Electronics America, M3087BFLBGP#U5 Datasheet - Page 356

• Manufacturer Part Number: M3087BFLBGP#U5
• Description: IC M32C/87 MCU FLASH 144LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M32C/80r

Specifications of M3087BFLBGP#U5

• Core Processor: M32C/80
• Core Size: 16/32-Bit
• Speed: 32MHz
• Connectivity: EBI/EMI, I²C, IEBus, IrDA, SIO, UART/USART
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 121
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 34x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 144-LQFP
• For Use With: R0K330879S001BE - KIT DEV RSK M32C/87R0K330879S000BE - KIT DEV RSK M32C/87
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M32C/87 Group (M32C/87, M32C/87A, M32C/87B)
REJ09B0180-0151 Rev.1.51 Jul 31, 2008
Page 332 of 587
Figure 22.11
Group 2 Waveform Generation Control Register i (i = 0 to 7)
b7 b6 b5 b4
NOTES:
1. SR waveform output mode is enabled only in even channels. In SR waveform output mode, the setting for the corresponding odd
2. To use the ISTXD2 pin or IEOUT pin as output, set bits MOD2 to MOD0 in the G2POCR0 register to 111b. To use the ISCLK2
3. When the RTP bit is set to 1, set bits MOD2 to MOD0 to 000b.
4. Real-time port output and parallel real-time port output cannot be used in the same group. To use parallel real-time port output,
5. When the RTP bit is set to 1, the INV bit setting is disabled.
6. If the INV or IVL bit is written while outputting waveform, the value written takes effect immediately on the output waveform.
channel (the channel followed by the even channel) is ignored. SR waveform can be output from even channels, and not from
odd channels.
pin as output, set bits MOD2 to MOD0 in the G2POCR1 register to 111b. Do not set bits MOD2 to MOD0 in registers G2POCR2
to G2POCR7 to 111b.
set the RTP bit to 1 and the PRT bit to 1 in the channel used for parallel real-time port output. Also, set the PRP bit in the
G2BCR1 register to 1.
b3
b2
G2POCR0 to G2POCR7 Registers
b1
b0
Bit Symbol
MOD0
MOD1
MOD2
PRT
RLD
RTP
INV
IVL
Symbol
G2POCR0 to G2POCR3
G2POCR4 to G2POCR7
Operating mode select bits
Parallel real-time port output
trigger select bit
Output level select bit
G2POi register value reload
timing select bit
Real-time port function
select bit
Inverted output function
select bit
(3)(4)
(5)(6)
Bit Name
(4)
(6)
(3)
Address
0150h, 0151h, 0152h, 0153h
0154h, 0155h, 0156h, 0157h
b2 b1 b0
0 0 0: Single waveform output mode
0 0 1: SR waveform output mode
0 1 0: Phase-delayed waveform output mode
0 1 1: Do not set to this value
1 0 0: Bit modulation PWM output mode
1 0 1: Do not set to this value
1 1 0: Do not set to this value
1 1 1: Use communication function output
0: Signal output when base timer matches the
1: Signal output when base timer matches the
0: "L" output
1: "H" output
0: Reload when written
1: Reload when the base timer is reset
0: Not used
1: Used (real-time port output mode or parallel
0: Output not inverted
1: Output inverted
G2POi register is not used as a trigger
G2POi register is used as a trigger
real-time port output mode)
Function
(1)
After Reset
00h
00h
(2)
22. Intelligent I/O
RW
RW
RW
RW
RW
RW
RW
RW
RW