UPD78F1506GF-GAT-AX Renesas Electronics America, UPD78F1506GF-GAT-AX Datasheet - Page 57

• Manufacturer Part Number: UPD78F1506GF-GAT-AX
• Description: MCU 16BIT 78K0R/LX3 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Lx3r

Specifications of UPD78F1506GF-GAT-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 78
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0R/Lx3
2.2.6 P50 to P57
output of LCD controller/driver.
(1) Port mode
R01UH0004EJ0401 Rev.4.01
Jul 2, 2010
P50 to P57 function as an I/O port. This port can also be used for serial interface data I/O, timer input, and segment
The following operation modes can be specified in 1-bit units.
P50/RxD3/SEGxx
P51/TxD3/SEGxx
P52/TI02/SEGxx
P53/TI04/SEGxx
P54/SEGxx
P55/SEGxx
P56/SEGxx
P57/SEGxx
(b) TOOL1
P50 to P57 function as an I/O port. P50 to P57 can be set to input or output port in 1-bit units using port mode
register 5 (PM5). Use of an on-chip pull-up resistor can be specified by pull-up resistor option register 5 (PU5).
This is a clock output pin for a debugger.
When the on-chip debug function is used, P41/TOOL1 pin can be used as follows by the mode setting on the
debugger.
Caution The function of the P40/TOOL0 pin varies as described in (a) to (c) below.
1-line mode: can be used as a port (P41).
2-line mode: used as a TOOL1 pin and cannot be used as a port (P41).
In the case of (b) or (c), make the specified connection.
(a) In normal operation mode and when on-chip debugging is disabled (OCDENSET = 0) by an
(b) In normal operation mode and when on-chip debugging is enabled (OCDENSET = 1) by an
(c) When on-chip debug function is used, or in write mode of flash memory programmer
option byte (000C3H)
=> Use this pin as a port pin (P40).
option byte (000C3H)
=> Connect this pin to V
=> Use this pin as TOOL0.
before reset release.
Directly connect this pin to the on-chip debug emulator or a flash memory programmer,
or pull it up by connecting it to V
(80 pins:
78F1501A, 78F1502A)
78K0R/LF3
√ (xx = 30)
√ (xx = 29)
√ (xx = 28)
√ (xx = 27)
√ (xx = 26)
√ (xx = 25)
√ (xx = 24)
√ (xx = 23)
μ
PD78F1500A,
DD
via an external resistor, and always input a high level to the pin
(100 pins:
DD
78F1504A, 78F1505A)
via an external resistor.
78K0R/LG3
√ (xx = 39)
√ (xx = 38)
√ (xx = 37)
√ (xx = 36)
√ (xx = 35)
√ (xx = 34)
√ (xx = 33)
√ (xx = 32)
μ
PD78F1503A,
CHAPTER 2 PIN FUNCTIONS
(128 pins:
78F1507A, 78F1508A)
78K0R/LH3
√ (xx = 53)
√ (xx = 52)
√ (xx = 51)
√ (xx = 50)
√ (xx = 49)
√ (xx = 48)
√ (xx = 47)
√ (xx = 46)
μ
PD78F1506A,
57