UPD78F1506GF-GAT-AX Renesas Electronics America, UPD78F1506GF-GAT-AX Datasheet - Page 728

• Manufacturer Part Number: UPD78F1506GF-GAT-AX
• Description: MCU 16BIT 78K0R/LX3 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Lx3r

Specifications of UPD78F1506GF-GAT-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 78
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0R/Lx3
R01UH0004EJ0401 Rev.4.01
Jul 2, 2010
Address: FFFBCH (DRC0), FFFBDH (DRC1)
Symbol
DRCn
(2) DMA operation control register n (DRCn)
DRCn is a register that is used to enable or disable transfer of DMA channel n.
Rewriting bit 7 (DENn) of this register is prohibited during operation (when DSTn = 1).
DRCn can be set by a 1-bit or 8-bit memory manipulation instruction.
Reset signal generation clears this register to 00H.
Cautions 1. The DSTn flag is automatically cleared to 0 when a DMA transfer is completed.
Remark
DMAC waits for a DMA trigger when DSTn = 1 after DMA operation is enabled (DENn = 1).
DMAC waits for a DMA trigger when DSTn = 1 after DMA operation is enabled (DENn = 1).
When a software trigger (STGn) or the start source trigger set by IFCn3 to IFCn0 is input, DMA transfer is started.
When DMA transfer is completed after that, this bit is automatically cleared to 0.
Write 0 to this bit to forcibly terminate DMA transfer under execution.
DENn
DENn
DSTn
<7>
0
1
0
1
n: DMA channel number (n = 0, 1)
2. When the FSEL bit of the OSMC register has been set to 1, do not enable (DENn = 1) DMA
Writing the DENn flag is enabled only when DSTn = 0. When a DMA transfer is terminated
without waiting for generation of the interrupt (INTDMAn) of DMAn, therefore, set DSTn to 0
and then DENn to 0 (for details, refer to 18.5.7 Forced termination by software).
operation for at least three clocks after the setting.
Figure 18-5. Format of DMA Operation Control Register n (DRCn)
Disables operation of DMA channel n (stops operating cock of DMA).
Enables operation of DMA channel n.
DMA transfer of DMA channel n is completed.
DMA transfer of DMA channel n is not completed (still under execution).
6
0
After reset: 00H
5
0
4
0
DMA operation enable flag
R/W
DMA transfer mode flag
3
0
CHAPTER 18 DMA CONTROLLER
2
0
1
0
DSTn
<0>
728