UPD78F1506GF-GAT-AX Renesas Electronics America, UPD78F1506GF-GAT-AX Datasheet - Page 963

• Manufacturer Part Number: UPD78F1506GF-GAT-AX
• Description: MCU 16BIT 78K0R/LX3 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Lx3r

Specifications of UPD78F1506GF-GAT-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 78
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0R/Lx3
R01UH0004EJ0401 Rev.4.01
Jul 2, 2010
Pin
functions
Memory
space
Processor
registers
Port
functions
Function
P110/ANO0,
P111/ANO1
P121 to P124
P150/ANI8/
AMP2+ to
P152/ANI10 and
P157/ANI15/
AV
REGC
PMC: Processor
mode control
register
Internal data
memory space
SFR: Special
function register
area
2nd SFR:
Extended special
function register
SP: Stack
pointer
P00/CAPH,
P01/CAPL,
P02/V
P10/SCK20/
SCL20,
P11/SI20/RxD2/
SDA20/INTP6
P12/TO02/SO20/
TxD2
P13/TO04/SO10
/TxD1
REFM
Details of
Function
LC3
When using at least one port of P110/ANO0 and P111/ANO1 as a digital port, set
AV
The function setting on P121 to P124 is available only once after the reset release.
The port once set for connection to an oscillator cannot be used as an input port
unless the reset is performed.
P150/ANI8/AMP2+ to P152/ANI10 and P157/ANI15/AV
(general-purpose port) mode after release of reset.
When using at least one port of P150/ANI8/AMP2+ to P152/ANI10 and
P157/ANI15/AV
figure.
Set PMC only once during the initial settings prior to operating the DMA controller.
Rewriting PMC other than during the initial settings is prohibited.
After setting PMC, wait for at least one instruction and access the mirror area.
When the
used, be sure to set bit 0 (MAA) of this register to 0.
It is prohibited to use the general-purpose register (FFEE0H to FFEFFH) space for
fetching instructions or as a stack area.
While using the self-programming function, the area of FFE20H to FFEFFH cannot
be used as a stack memory.
Do not access addresses to which SFRs are not assigned.
Do not access addresses to which 2nd SFRs are not assigned.
Since reset signal generation makes the SP contents undefined, be sure to initialize
the SP before using the stack.
To use P00/CAPH, P01/CAPL, and P02/V
(MDSET1) and bit 4 (MDSET0) of LCD mode register (LCDMD) to “0”, which is the
same as their default status setting.
To use P10/SCK20/SCL20 and P11/SI20/RxD2/SDA20/INTP6 as a general-purpose
port, note the serial array unit 1 setting. For details, refer to Table 14-9 Relationship
Between Register Settings and Pins (Channel 0 of unit 1: CSI20, UART2 Reception,
IIC20).
To use P12/TO02/SO20/TxD2 as a general-purpose port, set bit 2 (TO02) of timer
output register 0 (TO0) and bit 2 (TOE02) of timer output enable register 0 (TOE0) to
“0”, which is the same as their default status setting. And as a general-purpose port,
note the serial array unit 1 setting. For details of serial array unit 1 setting, refer to
Table 14-9 Relationship Between Register Settings and Pins (Channel 0 of unit 1:
CSI20, UART2 Reception, IIC20).
To use P13/TO04/SO10/TxD1 as a general-purpose port, set bit 4 (TO04) of timer
output register 0 (TO0) and bit 4 (TOE04) of timer output enable register 0 (TOE0) to
“0”, which is the same as their default status setting. And as a general-purpose port,
note the serial array unit 0 setting. For details of serial array unit 0 setting, refer to
Table 14-7 Relationship Between Register Settings and Pins (Channel 2 of unit 0:
CSI10, UART1 Transmission, IIC10)
Keep the wiring length as short as possible for the broken-line part in the above
DD1
to the same potential as EV
μ
PD78F1500A, 78F1503A, and 78F1506A (flash memory size: 64 KB) are
REFM
as a digital port, set AV
DD
or V
Cautions
DD
.
DD0
LC3
to the same potential as EV
as a general-purpose port, set bit 5
APPENDIX C LIST OF CAUTIONS
REFM
are set in the digital input
DD
or V
DD
.
96, 97
p.62
p.63
p.65
p.65
p.66
p.90
p.90
p.90
pp.90,
pp.90,
96
pp.91,
100
pp.91,
106
p.96
p.137
p.140
p.140
p.140
Page
(3/39)
963