UPD78F1506GF-GAT-AX Renesas Electronics America, UPD78F1506GF-GAT-AX Datasheet - Page 800

• Manufacturer Part Number: UPD78F1506GF-GAT-AX
• Description: MCU 16BIT 78K0R/LX3 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Lx3r

Specifications of UPD78F1506GF-GAT-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 78
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0R/Lx3
Note
Remark
R01UH0004EJ0401 Rev.4.01
Jul 2, 2010
Serial array units 0, 1
(SAU0, SAU1)
Serial interface IICA
LCD controller/driver
Multiplier/divider
Key interrupt
During reset signal generation or oscillation stabilization time wait, only the PC contents among the hardware
statuses become undefined. All other hardware statuses remain unchanged after reset.
The SFR and 2nd SFR mounted depend on the product. Refer to 3.2.4 Special function registers (SFRs)
and 3.2.5 Extended special function registers (2nd SFRs: 2nd Special Function Registers).
Table 22-2. Hardware Statuses After Reset Acknowledgment (3/4)
Serial data registers 00, 01, 02, 03, 10, 11, 12, 13 (SDR00, SDR01,
SDR02, SDR03, SDR10, SDR11, SDR12, SDR13)
Serial status registers 00, 01, 02, 03, 10, 11, 12, 13 (SSR00, SSR01,
SSR02, SSR03, SSR10, SSR11, SSR12, SSR13)
Serial flag clear trigger registers 00, 01, 02, 03, 10, 11, 13 (SIR00, SIR01,
SIR02, SIR03, SIR10, SIR11, SIR13)
Serial mode registers 00, 01, 02, 03, 10, 11, 12, 13 (SMR00, SMR01,
SMR02, SMR03, SMR10, SMR11, SMR12, SMR13)
Serial communication operation setting registers 00, 01, 02, 03, 10, 11, 12,
13 (SCR00, SCR01, SCR02, SCR03, SCR10, SCR11, SCR12,
SCR13)
Serial channel enable status registers 0, 1 (SE0, SE1)
Serial channel start trigger registers 0, 1 (SS0, SS1)
Serial channel stop trigger registers 0, 1 (ST0, ST1)
Serial clock select registers 0, 1 (SPS0, SPS1)
Serial output registers 0, 1 (SO0, SO1)
Serial output enable registers 0, 1 (SOE0, SOE1)
Shift register (IICA)
Control register 0 (IICCTL0)
Control register 1 (IICCTL1)
Slave address register (SVA)
IICA low-level width setting register 0 (IICWL)
IICA high-level width setting register 0 (IICWH)
Status register (IICS)
Flag register (IICF)
LCD mode register (LCDMD)
LCD display mode register (LCDM)
LCD clock control register 0 (LCDC0)
LCD boost level control register (VLCD)
Port function register (PFALL)
Segment enable register (SEGEN)
Input switch control register (ISC)
Multiplication/division data register A (MDAL, MDAH)
Multiplication/division data register B (MDBL, MDBH)
Multiplication/division data register C (MDCL, MDCH)
Multiplication/division control register (MDUC)
Key return mode register (KRM)
Hardware
CHAPTER 22 RESET FUNCTION
0000H
0000H
0000H
0020H
0087H
0000H
0000H
0000H
0000H
0F0FH
0000H
00H
00H
00H
00H
FFH
FFH
00H
00H
00H
00H
00H
0FH
00H
00H
00H
0000H
0000H
0000H
00H
00H
Acknowledgment
Status After Reset
Note
800