R5F2L3AAANFP#U1 Renesas Electronics America, R5F2L3AAANFP#U1 Datasheet - Page 747

• Manufacturer Part Number: R5F2L3AAANFP#U1
• Description: MCU FLASH 96+4KB 100LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/Lx/3AAr

Specifications of R5F2L3AAANFP#U1

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: LCD, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 88
• Program Memory Size: 96KB (96K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 20x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/L35A Group, R8C/L36A Group, R8C/L38A Group, R8C/L3AA Group,
R8C/L35B Group, R8C/L36B Group, R8C/L38B Group, R8C/L3AB Group
REJ09B0441-0100 Rev.1.00
Page 710 of 802
Figure 33.7
33.4.11.3 Program Command
The program command is used to write data to the flash memory in 1-byte or 1-word units.
When 40h is written in the first bus cycle and data is written in the second bus cycle to the write address, auto-
programming (data program and verify operation) starts. Make sure the address value specified in the first bus
cycle is the same address as the write address specified in the second bus cycle. Specify the even address to
program in word units.
The FST7 bit in the FST register can be used to confirm whether auto-programming has completed. The FST7
bit is set to 0 during auto-programming and is set to 1 when auto-programming completes.
After auto-programming has completed, the auto-program result can be confirmed by the FST4 bit in the FST
register (refer to 33.4.12 Full Status Check).
Do not write additions to the already programmed addresses.
The program command targeting each block in the program ROM can be disabled using the lock bit.
The following commands are not accepted under the following conditions:
•
•
•
•
Figure 33.7 shows a Program Flowchart (Flash Ready Status Interrupt Disabled) and Figure 33.8 shows a
Program Flowchart (Flash Ready Status Interrupt Enabled).
In EW1 mode, do not execute this command to any address where a rewrite control program is allocated.
When the RDYSTIE bit in the FMR0 register is set to 1 (flash ready status interrupt enabled), a flash ready
status interrupt can be generated upon completion of auto-programming. The auto-program result can be
confirmed by reading the FST register during the interrupt routine.
Block erase commands targeting data flash block A when the FMR14 bit in the FMR1 register is set to 1
(rewrite disabled).
Block erase commands targeting data flash block B when the FMR15 bit is set to 1 (rewrite disabled).
Block erase commands targeting data flash block C when the FMR16 bit is set to 1 (rewrite disabled).
Block erase commands targeting data flash block D when the FMR17 bit is set to 1 (rewrite disabled).
Program Flowchart (Flash Ready Status Interrupt Disabled)
Note: Specify the even address for the command code and data to program in
word units.
Oct 30, 2009
Write the command code 40h
(or, xx40)
Write data to the write address
Program completed
Set the FMR00 bit
Full status check
FST7 = 1?
(1)
Start
Yes
(1)
No
FST7: Bit in FST register
33. Flash Memory