LPC1837FET256,551 NXP Semiconductors, LPC1837FET256,551 Datasheet - Page 847

• Manufacturer Part Number: LPC1837FET256,551
• Description: Microcontrollers (MCU) 32BIT ARM CORTEX-M3 MCU 136KB SRAM
• Manufacturer: NXP Semiconductors
• Series: LPC18xxr

Specifications of LPC1837FET256,551

• Core: ARM Cortex M3
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 150MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, SD/MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 80
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 136K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-LBGA
• Lead Free Status / Rohs Status: Details
• Other names: 935293795551

NXP Semiconductors
<Document ID>
User manual
36.7.3.9 Handling of received messages
Table 796. Initialization of a receive object
The Arbitration Registers (ID28-0 and XTD bit) are given by the application. They define
the identifier and type of accepted received messages. If an 11-bit Identifier (“Standard
Frame”) is used, it is programmed to ID28 to ID18. ID17 to ID0 can then be disregarded.
When a Data Frame with an 11-bit Identifier is received, ID17 to ID0 will be set to ‘0’.
If the RxIE bit is set, the INTPND bit will be set when a received Data Frame is accepted
and stored in the Message Object.
The Data Length Code (DLC[3:0] is given by the application. When the Message Handler
stores a Data Frame in the Message Object, it will store the received Data Length Code
and eight data bytes. If the Data Length Code is less than 8, the remaining bytes of the
Message Object will be overwritten by non specified values.
The Mask Registers (Msk[28:0], UMASK, MXTD, and MDIR bits) may be used
(UMASK=’1’) to allow groups of Data Frames with similar identifiers to be accepted. For
details see section
applications.
The CPU may read a received message any time via the IFx Interface registers. The data
consistency is guaranteed by the Message Handler state machine.
To transfer the entire received message from message RAM into the message buffer,
software must write first 0x007F to the Command Mask Register and then the number of
the Message Object to the Command Request Register. Additionally, the bits NEWDAT
and INTPND are cleared in the Message RAM (not in the Message Buffer).
If the Message Object uses masks for acceptance filtering, the arbitration bits show which
of the matching messages has been received.
The actual value of NEWDAT shows whether a new message has been received since
last time this Message Object was read. The actual value of MSGLST shows whether
more than one message has been received since last time this Message Object was read.
MSGLST will not be automatically reset.
Using a Remote Frame, the CPU may request another CAN node to provide new data for
a receive object. Setting the TXRQST bit of a receive object will cause the transmission of
a Remote Frame with the receive object’s identifier. This Remote Frame triggers the other
CAN node to start the transmission of the matching Data Frame. If the matching Data
Frame is received before the Remote Frame could be transmitted, the TXRQST bit is
automatically reset.
MSGVAL
MSGLST
1
0
Arbitration
application
dependent
application
dependent
All information provided in this document is subject to legal disclaimers.
RXIE
bits
Section
Rev. 00.13 — 20 July 2011
application
dependent
Data bits
36.7.3.4.1. The DIR bit should not be masked in typical
TXIE
0
application
dependent
Mask bits
INTPND
0
RMTEN
EOB
1
0
Chapter 36: LPC18xx C_CAN
DIR
0
UM10430
TXRQST
© NXP B.V. 2011. All rights reserved.
0
NEWDAT
847 of 1164
0