UPD70F3740GC-UEU-AX Renesas Electronics America, UPD70F3740GC-UEU-AX Datasheet - Page 883

• Manufacturer Part Number: UPD70F3740GC-UEU-AX
• Description: MCU 32BIT V850ES/JX3 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3r

Specifications of UPD70F3740GC-UEU-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 32MHz
• Connectivity: CSI, EBI/EMI, I²C, UART/USART
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 84
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 2.85 V ~ 3.6 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

V850ES/JG3
R01UH0015EJ0300 Rev.3.00
Sep 30, 2010
On-chip
debug
function
Electrical
specifica-
tions
Function
Cautions (other
than DUC)
Security ID
Absolute
maximum
ratings
Main clock
oscillator
characteristics
Subclock
oscillator
characteristics
Details of
Function
The standby mode is released by the pseudo RRM function and DMM function if
one of the following conditions is satisfied.
• Mode for communication between MINICUBE2 and the target device is CSIB0
• Mode for communication between MINICUBE2 and the target device is
Peripheral I/O registers that requires a specific sequence cannot be written with
the DMM function.
If a space where the debug monitor program is allocated is rewritten by flash self
programming, the debugger can no longer operate normally.
After the flash memory is erased, 1 is written to the entire area.
Be sure not to exceed the absolute maximum ratings (MAX. value) of each supply
voltage.
Do not directly connect the output (or I/O) pins of IC products to each other, or to
V
directly connected to each other.
Direct connection of the output pins between an IC product and an external circuit
is possible, if the output pins can be set to the high-impedance state and the
output timing of the external circuit is designed to avoid output conflict.
Product quality may suffer if the absolute maximum rating is exceeded even
momentarily for any parameter. That is, the absolute maximum ratings are rated
values at which the product is on the verge of suffering physical damage, and
therefore the product must be used under conditions that ensure that the absolute
maximum ratings are not exceeded. The ratings and conditions indicated for DC
characteristics and AC characteristics represent the quality assurance range
during normal operation.
The oscillation frequency shown above indicates only oscillator characteristics.
Use the V850ES/JG3 so that the internal operation conditions do not exceed the
ratings shown in AC Characteristics and DC Characteristics.
Time required to set up the flash memory. Secure the setup time using the OSTS
register.
When using the main clock oscillator, wire as follows in the area enclosed by the
broken lines in the above figure to avoid an adverse effect from wiring
capacitance.
• Keep the wiring length as short as possible.
• Do not cross the wiring with the other signal lines.
• Do not route the wiring near a signal line through which a high fluctuating
• Always make the ground point of the oscillator capacitor the same potential as
• Do not ground the capacitor to a ground pattern through which a high current
• Do not fetch signals from the oscillator.
When the main clock is stopped and the device is operating on the subclock, wait
until the oscillation stabilization time has been secured by the program before
switching back to the main clock.
For the resonator selection and oscillator constant, customers are requested to
either evaluate the oscillation themselves or apply to the resonator manufacturer
for evaluation.
The oscillation frequency shown above indicates only oscillator characteristics.
Use the V850ES/JG3 so that the internal operation conditions do not exceed the
ratings shown in AC Characteristics and DC Characteristics.
DD
current flows.
V
flows.
or CSIB3
UARTA0, and the main clock has been supplied.
SS
, V
.
CC
, and GND. Open-drain pins or open-collector pins, however, can be
Cautions
APPENDIX E LIST OF CAUTIONS
Page 867 of 870
p. 761
p. 761
p. 761
p. 762
p. 765
p. 766
p. 766
p. 768
p. 768
p. 768
p. 768
p. 768
p. 770
Page
(34/36)