UPD70F3451GC-UBT-A Renesas Electronics America, UPD70F3451GC-UBT-A Datasheet - Page 207

• Manufacturer Part Number: UPD70F3451GC-UBT-A
• Description: MCU 32BIT 128KB FLASH 80LQFP
• Manufacturer: Renesas Electronics America
• Series: V850E/Ix3r

Specifications of UPD70F3451GC-UBT-A

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: CSI, I²C, UART/USART
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 44
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3.5 V ~ 5.5 V
• Data Converters: A/D 10x12b, 4x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

(5) TAAm I/O control register 2 (TAAmIOC2)
Note V850E/IG3 only
Cautions 1. Rewrite the TAAmEES1, TAAmEES0, TAAmETS1, and TAAmETS0 bits when the
The TAAmIOC2 register is an 8-bit register that controls the valid edge for the external event count input signal
(TIAm0 pin) and external trigger input signal (TIAm0 pin).
This register can be read or written in 8-bit or 1-bit units.
Reset sets this register to 00H.
2. The TAAmEES1 and TAAmEES0 bits are valid only when the TAAmCTL1.TAAmEEE bit = 1
3. The TAAmETS1 and TAAmETS0 bits are valid only in the external trigger pulse mode or
V850E/IF3
V850E/IG3
TAAmIOC2
m = 2, 4
m = 2 to 4
TAAmCTL0.TAAmCE bit = 0. (The same value can be written when the TAAmCE bit = 1.) If
rewriting was mistakenly performed, clear the TAAmCE bit to 0 and then set the bits again.
or
TAAmCTL1.TAAmMD0 bits = 001) has been set.
one-shot pulse output mode.
After reset: 00H
when
TAAmEES1
TAAmETS1
CHAPTER 6 16-BIT TIMER/EVENT COUNTER AA (TAA)
0
0
1
1
0
0
1
1
7
0
the
TAAmEES0
TAAmETS0
R/W
external
6
0
0
1
0
1
0
1
0
1
Address:
User’s Manual U18279EJ3V0UD
External event count input signal (TIAm0 pin) valid edge setting
No edge detection (external event count invalid)
Detection of rising edge
Detection of falling edge
Detection of both edges
No edge detection (external trigger invalid)
Detection of rising edge
Detection of falling edge
Detection of both edges
External trigger input signal (TIAm0 pin) valid edge setting
5
0
event
TAA2IOC2 FFFFF6A4H, TAA3IOC2 FFFFFB04H
TAA4IOC2 FFFFFB24H
4
0
count
TAAmEES1 TAAmEES0 TAAmETS1 TAAmETS0
mode
3
(the
2
TAAmCTL1.TAAmMD2
1
0
Note
,
to
205