TMP92xy26AXBG Toshiba, TMP92xy26AXBG Datasheet - Page 614

• Manufacturer Part Number: TMP92xy26AXBG
• Manufacturer: Toshiba

Specifications of TMP92xy26AXBG

• Package: FPGA228
• Rom Types(m=mask,p=otp, F=flash,e=eeprom): Romless
• Rom Combinations: Romless
• Ram Combinations: 144/288
• Architecture: 32-bit CISC
• Usb/spi Channels: 1/1
• Uart/sio Channels: 2
• I2c/sio Bus Channels: 1
• (s)dram Controller: 1
• Adc 10-bit Channel: 6
• Da Converter: -
• Timer 8-bit Channel: 8
• Timer 16-bit Channel: 2
• Pwm 8-bit Channels: -
• Pwm 16-bit Channels: -
• Cs/wait Controller: 4
• Dual Clock: Y
• Number Of I/o Ports: 136
• Power Supply Voltage(v): 3.0 to 3.6

ADMOD5
(12BDH)
ADMOD4
(12BCH)
bit Symbol
Read/Write
Reset State
Function
Note: When AD monitor function interrupts generate, it is cleared automatically and it is set to disable condition.
bit Symbol
Read/Write
Reset State
Function
Note1: When converting AD in hard ware trigger by setting <HHTRGE> and <HTRGE>to “1”, set PGFC<PG3F> to
Note 2: When disabling an external trigger (
Note 3: When starting AD by using external trigger (ADTRG), it can be started after enabling (<HHTRGE> = “1” or
Note 4: When chaging compare register value of AD Monitor function, change it after setting AD Monitor function to
“1” (as ADTRG) in case of external TRG before enabling it. When using an INTTBx0 of 16-bit timer, first set the
<TSEL1:0> or <HTSEL1:0> bit to “00” when the timer is not operating. Then, set the <HHTRGE> and <HTRGE>
to “1” and enable trigger operation. Finally, operate the timer so that AD conversion will be initiated at constant
intervals.
“0”, and clear the PGFC<PG3F> to “0”, thus configuring port G as a general-purpose port.
<HTRGE> = “1”) and 3 clock at f
disable(ADMOD4<CMEN1:0> = “0”).
AD Monitor
function1
0: Disable
1: Enable
AD Mode Control Register 4 (AD Monitor function control)
AD Mode Control Register 5 (AD Monitor function control)
CMEN1
7
7
0
Figure 3.23.5 AD Conversion Registers
AD Monitor
function0
0: Disable
1: Enable
Select analog channel for AD monitor
function 1
000: AN0
001: AN1
010: AN2
011: AN3
C1MCH2
CMEN0
6
6
0
0
SYS
0: less than
1: Greater
Generation
condition of
AD monitor
function
interrupt 1
CM1CH1
than or
Equal
CMP1C
100: AN4
101: AN5
110: Reserved
111: Reserved
92CF26A-612
was executed. AD is not started when before that time.
R/W
ADTRG
5
5
0
0
R/W
) for AD conversion, first clear the <HHTRGE> or <HTRGE> bit to
0: less than
1: Greater
Generation
condition of
AD monitor
function
interrupt 0
CM1CH0
than or
Equal
CMP0C
4
4
0
0
AD monitor
function
interrupt 1
0: Disable
1: Enable
(Note)
IRQEN1
3
3
0
AD monitor
function
interrupt 0
0: Disable
1: Enable
(Note)
Select analog channel for AD monitor
function 0
000: AN0
001: AN1
010: AN2
011: AN3
CM0CH2
IRQEN0
2
2
0
0
0: No
1:
Status of
AD monitor
function
interrupt 1
CMPINT1
CM0CH1
generation
Generation
100: AN4
101: AN5
110: Reserved
111: Reserved
R/W
1
1
0
0
TMP92CF26A
R
0: No
1:
Status of
AD monitor
function
interrupt 0
CMPINT0
CM0CH0
2009-06-25
generation
Generation
0
0
0
0