TMP92xy26AXBG Toshiba, TMP92xy26AXBG Datasheet - Page 635
TMP92xy26AXBG
Manufacturer Part Number
TMP92xy26AXBG
Description
Manufacturer
Toshiba
Datasheet
1.TMP92XY26AXBG.pdf
(768 pages)
Specifications of TMP92xy26AXBG
Package
FPGA228
Rom Types(m=mask,p=otp, F=flash,e=eeprom)
Romless
Rom Combinations
Romless
Ram Combinations
144/288
Architecture
32-bit CISC
Usb/spi Channels
1/1
Uart/sio Channels
2
I2c/sio Bus Channels
1
(s)dram Controller
1
Adc 10-bit Channel
6
Da Converter
-
Timer 8-bit Channel
8
Timer 16-bit Channel
2
Pwm 8-bit Channels
-
Pwm 16-bit Channels
-
Cs/wait Controller
4
Dual Clock
Y
Number Of I/o Ports
136
Power Supply Voltage(v)
3.0 to 3.6
- Current page: 635 of 768
- Download datasheet (6Mb)
3.25.2
• Entering the Power Cut Mode
Note: As soon as the PMCCTL<PCM_ON> bit is set to 1, the power management signal (PWE) changes from 1 to 0
converter. Then, configure the output pins to function as ports through the Pn, PnCR and
PnDR registers. At this time, the PM7 pin should be configured as the PWE input pin. Also,
the internal RTC pin and the external interrupt pins that are used for waking up from the
Power Cut mode should be configured as interrupt inputs and enabled.
the INT4 pin is used as the TSI input, the debounce circuit should be disabled.
46000H to 49FFFH.
waking up should be predefined in this wake-up program.)
the Power Cut mode (the time period required for the power supply voltage and the
high-frequency clock to stabilize) by the PMCCTL<WUTM1:0> bits. Power Cut mode is
then entered by writing a 1 to the PMCCTL<PCM_ON> bit.
external I/O and PMC.
Detailed Description of Mode Transitions
When entering the Power Cut mode, the CPU needs to be executing in the on-chip RAM.
The low-frequency clock (XT) must be enabled.
It is also necessary to disable interrupts, and to stop DMA operations, WDT and AD
The interrupt inputs should be configured as rising-edge triggered, if configurable. When
The wake-up program must be prewritten to the on-chip RAM area at addresses from
(Including the initial setting of the WDT and other registers, all the required settings for
Finally, stop the PLL if it is operated, and specify the warm-up time for waking up from
At this time, the RESET (HOT_RESET) signal is asserted to all the circuits excluding the
This section explains the procedures for entering and exiting the Power Cut mode.
and external power supplies are turned off.
92CF26A-633
TMP92CF26A
2009-06-25
Related parts for TMP92xy26AXBG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Toshiba Semiconductor [TOSHIBA IGBT Module Silicon N Channel IGBT]
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA GTR MODULE SILICON NPN TRIPLE DIFFUSED TYPE
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA GTR Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA Intelligent Power Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA INTELLIGENT POWER MODULE SILICON N CHANNEL LGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA IGBT Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA GTR MODULE SILICON N−CHANNEL IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA Intelligent Power Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA GTR Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA INTELLIGENT POWER MODULE
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA Intelligent Power Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA Intelligent Power Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA IGBT Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA Intelligent Power Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
Toshiba Semiconductor [SILICON N CHANNEL 1GBT]
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet: