MCBSTM32EXL Keil, MCBSTM32EXL Datasheet - Page 286
MCBSTM32EXL
Manufacturer Part Number
MCBSTM32EXL
Description
BOARD EVALUATION FOR STM32F103ZE
Manufacturer
Keil
Specifications of MCBSTM32EXL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 286 of 995
- Download datasheet (9Mb)
Advanced-control timers (TIM1&TIM8)
286/995
repetition counter, trigger output features continue to work as normal. Encoder mode and
External clock mode 2 are not compatible and must not be selected together.
In this mode, the counter is modified automatically following the speed and the direction of
the incremental encoder and its content, therefore, always represents the encoder’s
position. The count direction correspond to the rotation direction of the connected sensor.
The table summarizes the possible combinations, assuming TI1 and TI2 don’t switch at the
same time.
Table 71.
An external incremental encoder can be connected directly to the MCU without external
interface logic. However, comparators are normally be used to convert the encoder’s
differential outputs to digital signals. This greatly increases noise immunity. The third
encoder output which indicate the mechanical zero position, may be connected to an
external interrupt input and trigger a counter reset.
The
direction control. It also shows how input jitter is compensated where both edges are
selected. This might occur if the sensor is positioned near to one of the switching points. For
this example we assume that the configuration is the following:
●
●
●
●
●
●
Active edge
Counting on
Counting on
Counting on
TI1 and TI2
TI1 only
TI2 only
Figure 92
CC1S=’01’ (TIMx_CCMR1 register, TI1FP1 mapped on TI1).
CC2S=’01’ (TIMx_CCMR2 register, TI1FP2 mapped on TI2).
CC1P=’0’ (TIMx_CCER register, TI1FP1 non-inverted, TI1FP1=TI1).
CC2P=’0’ (TIMx_CCER register, TI1FP2 non-inverted, TI1FP2= TI2).
SMS=’011’ (TIMx_SMCR register, both inputs are active on both rising and falling
edges).
CEN=’1’ (TIMx_CR1 register, Counter enabled).
Counting direction versus encoder signals
gives an example of counter operation, showing count signal generation and
signal (TI1FP1
for TI2, TI2FP2
opposite
Level on
for TI1)
High
High
High
Low
Low
Low
Doc ID 13902 Rev 9
No Count
No Count
Rising
Down
Down
Up
Up
TI1FP1 signal
No Count
No Count
Falling
Down
Down
Up
Up
No Count
No Count
Rising
Down
Down
Up
Up
TI2FP2 signal
No Count
No Count
Falling
Down
Down
Up
Up
RM0008
Related parts for MCBSTM32EXL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KEIL C-COMPILER (US ONLY)
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
KEIL C-COMPILER INTERNATIONAL
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
KEIL C-COMPILER US VERSION
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
DEV KIT FOR STM32
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER FOR STM32
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER FOR STM32F10XE MCU
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER KEIL FOR STR910
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Microcontroller Modules & Accessories KEIL ULINK PRO 5V ADAPTOR KIT
Manufacturer:
Keil Software
Part Number:
Description:
Development Boards & Kits - ARM KEIL NUVOTON EVAL BD CORTEX-M0 + ULINK-ME
Manufacturer:
Keil Tools
Datasheet:
Part Number:
Description:
Development Boards & Kits - ARM KEIL NUVOTON EVAL BD CORTEX-M0
Manufacturer:
Keil Tools
Datasheet:
Part Number:
Description:
BOARD EVAL FOR LPC213X ARM MCU
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
K60N512 Keil Tower Kit
Manufacturer:
Freescale Semiconductor
Datasheet: