MCBSTM32EXL Keil, MCBSTM32EXL Datasheet - Page 84
MCBSTM32EXL
Manufacturer Part Number
MCBSTM32EXL
Description
BOARD EVALUATION FOR STM32F103ZE
Manufacturer
Keil
Specifications of MCBSTM32EXL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 84 of 995
- Download datasheet (9Mb)
Low-, medium- and high-density reset and clock control (RCC)
6.3.2
84/995
ADC PRE[1:0]
31
15
rw
30
14
rw
Bits 15:8 HSICAL[7:0]: Internal high-speed clock calibration
Bits 7:3 HSITRIM[4:0]: Internal high-speed clock trimming
Bit 16 HSEON: External high-speed clock enable
Reserved
Clock configuration register (RCC_CFGR)
Address offset: 0x04
Reset value: 0x0000 0000
Access: 0 wait state 2, word, half-word and byte access
1 or 2 wait states inserted only if the access occurs during clock source switch.
Bit 2
Bit 1 HSIRDY: Internal high-speed clock ready flag
Bit 0 HSION: Internal high-speed clock enable
29
13
rw
PPRE2[2:0]
Reserved, always read as 0.
Set and cleared by software.
Cleared by hardware to stop the external 1-25MHz oscillator when entering in Stop or
Standby mode. This bit cannot be reset if the external 4-25 MHz oscillator is used directly or
indirectly as the system clock or is selected to become the system clock.
0: HSE oscillator OFF
1: HSE oscillator ON
These bits are initialized automatically at startup.
These bits provide an additional user-programmable trimming value that is added to the
HSICAL[7:0] bits. It can be programmed to adjust to variations in voltage and temperature
that influence the frequency of the internal HSI RC.
The default value is 16, which, when added to the HSICAL value, should trim the HSI to 8
MHz ± 1%. The trimming step (F
steps.
Set by hardware to indicate that internal 8 MHz RC oscillator is stable. After the HSION bit is
cleared, HSIRDY goes low after 6 internal 8 MHz RC oscillator clock cycles.
0: internal 8 MHz RC oscillator not ready
1: internal 8 MHz RC oscillator ready
Set and cleared by software.
Set by hardware to force the internal 8 MHz RC oscillator ON when leaving Stop or Standby
mode or in case of failure of the external 4-25 MHz oscillator used directly or indirectly as
system clock. This bit cannot be reset if the internal 8 MHz RC is used directly or indirectly
as system clock or is selected to become the system clock.
0: internal 8 MHz RC oscillator OFF
1: internal 8 MHz RC oscillator ON
28
12
rw
27
11
rw
26
rw
10
rw
PPRE1[2:0]
MCO[2:0]
25
rw
rw
9
Doc ID 13902 Rev 9
24
rw
rw
8
hsitrim
Res.
23
rw
7
) is around 40 kHz between two consecutive HSICAL
USB
PRE
22
rw
rw
HPRE[3:0]
6
21
rw
rw
5
PLLMUL[3:0]
20
rw
rw
4
19
rw
3
r
SWS[1:0]
18
rw
2
r
XTPRE
PLL
17
rw
rw
1
SW[1:0]
RM0008
SRC
PLL
16
rw
rw
0
Related parts for MCBSTM32EXL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KEIL C-COMPILER (US ONLY)
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
KEIL C-COMPILER INTERNATIONAL
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
KEIL C-COMPILER US VERSION
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
DEV KIT FOR STM32
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER FOR STM32
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER FOR STM32F10XE MCU
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
KIT STARTER KEIL FOR STR910
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Microcontroller Modules & Accessories KEIL ULINK PRO 5V ADAPTOR KIT
Manufacturer:
Keil Software
Part Number:
Description:
Development Boards & Kits - ARM KEIL NUVOTON EVAL BD CORTEX-M0 + ULINK-ME
Manufacturer:
Keil Tools
Datasheet:
Part Number:
Description:
Development Boards & Kits - ARM KEIL NUVOTON EVAL BD CORTEX-M0
Manufacturer:
Keil Tools
Datasheet:
Part Number:
Description:
BOARD EVAL FOR LPC213X ARM MCU
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
K60N512 Keil Tower Kit
Manufacturer:
Freescale Semiconductor
Datasheet: